Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the power switch is on (IG), the battery voltage is applied to terminal IGSW of the ECM (included in the hybrid vehicle control ECU). The ECM MREL output signal causes a current to flow to the coil, closing the contacts of the IGCT relay and supplying power to terminal +B of the ECM.
If the power switch is turned off, the ECM holds the IGCT relay ON for a maximum of 2 seconds to allow for the initial setting of the throttle valve.
When the power switch is on (IG), voltage from the ECM's MREL terminal flows to the IGCT relay. This causes the contacts of the IGCT relay to close, which supplies power to terminal +B or +B1 of the ECM.

WIRING DIAGRAM


A184167E01


INSPECTION PROCEDURE

1.INSPECT HYBRID VEHICLE CONTROL ECU (+B1, +B2 VOLTAGE)


    A178675E05
  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A43-2 (+B1) - B3-5 (E1)
    Always
    11 to 14 V
    A43-1 (+B2) - B3-5 (E1)
    Always
    11 to 14 V



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE 

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)


    A178676E02
  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B3-5 (E1) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the hybrid vehicle control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)
OK


3.INSPECT HYBRID VEHICLE CONTROL ECU (IGSW VOLTAGE)


    A178675E06
  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D35-9 (IGSW) - B3-5 (E1)
    Always
    11 to 14 V



NG
Go to step 9
OK


4.INSPECT HYBRID VEHICLE CONTROL ECU (MREL VOLTAGE)


    A178675E07
  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A43-12 (MREL) - B3-5 (E1)
    Always
    11 to 14 V



NG
Go to step 5
OK

REPLACE HYBRID VEHICLE CONTROL ECU 

5.CHECK FUSE (IGCT NO. 2 FUSE)


    A179779E01
  1. Remove the IGCT No. 2 fuse from the engine room relay block No. 2.

  1. Measure the IGCT No. 2 fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the IGCT No. 2 fuse.



NG
REPLACE FUSE (IGCT NO. 2 FUSE)
OK


6.INSPECT IGCT RELAY


    A092673
  1. Remove the IGCT relay from the engine room relay block.

  1. Measure the IGCT relay resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    Below 1 Ω
    (Apply battery voltage between terminals 1 and 2)



NG
REPLACE IGCT RELAY
OK


7.CHECK HARNESS AND CONNECTOR (IGCT RELAY- HYBRID VEHICLE CONTROL ECU)


    A179784E03
  1. Remove the IGCT relay from the engine room relay block.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (IGCT Relay) - A43-12 (MREL)
    Always
    Below 1 Ω

  1. Reinstall the IGCT relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGCT RELAY- HYBRID VEHICLE CONTROL ECU)
OK


8.CHECK HARNESS AND CONNECTOR


    A179785E02
  1. Remove the IGCT relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified condition
    1 (IGCT relay) - Body ground
    Always
    Below 1 Ω

  1. Reinstall the IGCT relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK AND REPAIR HARNESS AND CONNECTOR (TERMINAL +B OF HV CONTROL ECU - BATTERY POSITIVE TERMINAL) 

9.CHECK FUSE (IGN FUSE)


    A168236E05
  1. Remove the IGN fuse from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Condition
    Condition
    Specified Condition
    IGN fuse
    Always
    Below 1 Ω

  1. Reinstall the IGN fuse.



NG
REPLACE FUSE (IGN FUSE)
OK


10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - IG2 RELAY)


    A179768E01
  1. Remove the IG2 relay from the engine room relay block.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IG2 relay terminal 3 - D35-9 (IGSW)
    Always
    Below 1 Ω

  1. Reconnect the ECM connector.

  1. Reinstall the IG2 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (HYBRID VEHICLE CONTROL ECU - IG2 RELAY)
OK


11.INSPECT IG2 RELAY


    B016200
  1. Remove the IG2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When no battery voltage applied to terminals 1 and 2
    10 kΩ or higher
    When battery voltage applied to terminals 1 and 2
    Below 1 Ω

  1. Reinstall the IG2 relay.



NG
REPLACE IG2 RELAY
OK


12.CHECK FUSE (IG2 FUSE)


    A179777E05
  1. Remove the IG2 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IG2 fuse
    Always
    Below 1 Ω

  1. Reinstall the IG2 fuse



NG
REPLACE FUSE (IG2 FUSE)
OK


13.CHECK HARNESS AND CONNECTOR (IG2 RELAY POWER SOURCE)


    A172712E01
  1. Remove the IG2 relay from the engine room relay block.

  1. Turn the power switch on (IG)

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    5 - Body ground
    Power switch on (IG)
    9 to 14 V

  1. Reinstall the IG2 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - BATTERY)
OK


14.CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND)


    A172712E01
  1. Remove the IG2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    2 - Body ground
    Always
    Below 1 Ω

  1. Reinstall the IG2 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - BODY GROUND)
OK


15.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - MAIN BODY ECU)


    A172719E02
  1. Remove the IG2 relay from the engine room relay block.

  1. Remove the instrument panel junction block (main body ECU).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    IG2 relay holder terminal (1) - D7-11 (IG2D)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D7-11 (IG2D) - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the IG2 relay.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM RELAY BLOCK - MAIN BODY ECU)
OK

CHECK SMART KEY SYSTEM (Click here)