Home › BRAKE › BRAKE › BRAKE MASTER CYLINDER

BRAKE MASTER CYLINDER > ON-VEHICLE INSPECTION

for Preparation Click here


NOTICE:
A DTC may be stored during the inspection procedure. Be sure to clear the DTC and check that a normal system code is output after the inspection is finished.



1. CHECK BRAKE MASTER CYLINDER
  1. Check battery voltage.

    Standard voltage:
    11 to 14 V (while the power switch is off)

  1. Connect the Techstream and the pedal effort gauge.

    1. Connect the pedal effort gauge.

    2. Move the shift lever to the P position. Apply the parking brake and connect the Techstream to the DLC3.

    3. Turn the power switch on (IG).

    4. Clear the DTCs (Click here).

  1. Check operation without the brake booster.

    1. Inspect and adjust the brake pedal height .

    2. Inspect and adjust the brake pedal stroke sensor .

    3. Inspect the brake pedal free play .

    4. Inspect the brake pedal reserve distance .

    5. Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Electronically Controlled Brake system Utility / Electronically Controlled Brake system Invalid to prohibit the brake control.

    6. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List "Master Cylinder Sensor", "Master Cylinder Sensor 2", "Stroke Sensor" and "Stroke Sensor 2".

    7. Check the value output from "Master Cylinder Sensor", "Master Cylinder Sensor 2", "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.

      Standard voltage:

      Pedal Effort
      N (kgf, lbf)
      Master Cylinder Sensor
      (V)
      Master Cylinder Sensor 2
      (V)
      Stroke Sensor
      (V)
      Stroke Sensor 2
      (V)
      200 (20.4, 45.0)
      0.90 to 1.30
      0.90 to 1.30
      1.60 to 2.00
      2.95 to 3.35
      500 (51, 112.4)
      1.95 to 2.35
      1.95 to 2.35
      2.00 to 2.40
      2.55 to 2.95

    8. Finish the brake control prohibition on the Techstream.



2. CHECK STROKE SIMULATOR
  1. Check battery voltage.

    Standard voltage:
    11 to 14 V (while the power switch is off)

  1. Connect the Techstream and the pedal effort gauge.

    1. Connect the pedal effort gauge.

    2. Move the shift lever to the P position. Apply the parking brake and connect the Techstream to the DLC3.

    3. Turn the power switch on (IG).

    4. Clear the DTCs (Click here).

  1. Check operation without the brake booster.

    1. Inspect and adjust the brake pedal height .

    2. Inspect and adjust the brake pedal stroke sensor .

    3. Inspect the brake pedal free play .

    4. Inspect the brake pedal reserve distance .

    5. Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Electronically Controlled Brake system Utility / Electronically Controlled Brake system Invalid to prohibit the brake control.

    6. Enter the following menus: Chassis / ABS/VSC/TRAC /Data List "Master Cylinder Sensor", "Master Cylinder Sensor 2", "Stroke Sensor" and "Stroke Sensor 2".

    7. Check the value output from "Voltage of Master Cylinder Sensor", "Voltage of Master Cylinder Sensor 2", "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.

      Standard voltage:

      Pedal Effort
      N (kgf, lbf)
      Master Cylinder Sensor
      (V)
      Master Cylinder Sensor 2
      (V)
      Stroke Sensor
      (V)
      Stroke Sensor 2
      (V)
      200 (20.4, 45.0)
      0.90 to 1.30
      0.90 to 1.30
      1.60 to 2.00
      2.95 to 3.35
      500 (51, 112.4)
      1.95 to 2.35
      1.95 to 2.35
      2.00 to 2.40
      2.55 to 2.95

    8. Finish the brake control prohibition on the Techstream.

  1. Check operation with the brake booster.

    1. Turn the power switch on (IG).

    2. Enter the following menus: Chassis / ABS/VSC/TRAC /Data List "Stroke Sensor" and "Stroke Sensor 2".

    3. Depress the brake pedal 4 or 5 times.

    4. Check the value output from "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.

      Standard voltage:

      Pedal Effort
      N (kgf, lbf)
      Stroke Sensor
      (V)
      Stroke Sensor 2
      (V)
      50 (5.1 11.2)
      1.15 to 1.55
      3.4 to 3.8
      100 (10.2, 22.4)
      1.3 to 1.7
      3.25 to 3.65
      150 (15.3, 34.0)
      1.4 to 1.8
      3.15 to 3.55
      200 (20.4, 45.0)
      1.5 to 1.9
      3.05 to 3.45