Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

ELECTRONICALLY CONTROLLED BRAKE SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK AUXILIARY BATTERY VOLTAGE
  1. Check the auxiliary battery voltage.

    Standard voltage:
    11 to 14 V


SKID CONTROL ECU INSPECTION
  1. Measure the voltage between each terminal or between each terminal and body ground.

  2. Connect the Techstream to the DLC3, and check the communication condition with the skid control ECU.



  3. Using an oscilloscope, check the pulse generated between each terminal or between each terminal and body ground.

    NOTICE:
    1. Inspection should be performed from the back of the connector with the connector connected to the skid control ECU.
    2. The voltage between the terminals of the brake actuator assembly may become 0 V due to the fail safe function when the brake warning light / yellow (minor malfunction) comes on (malfunctioning).


    C138589E04

    HINT:
    Inspect the ECU from the wire harness side while the connector is connected.


    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A46-1 (GND1) - Body ground
    W-B - Body ground
    Skid control ECU ground 1
    Always
    Below 1 Ω
    A46-2 (R1+) - Body ground
    G - Body ground
    ABS main relay power 1
    Power switch on (IG)
    9.1 to 13.6 V
    A46-3 (BS1) - Body ground
    L - Body ground
    Battery source 1
    Approx. 1.5 seconds after turning power switch on (IG)
    8.8 to 14 V
    A46-4 (SMC1) - Body ground
    R - Body ground
    Master cut solenoid 1 output
    Brake pedal depressed approx. 1.5 seconds after turning power switch on (IG)
    Below 1.5 V
    A46-5 (+BCTY) - Body ground
    V - Body ground
    Courtesy power input
    Driver door open → close
    Approx. 5 sec. 8 to 16 V
    → Below 1 V
    A46-6 (SLAFR-) - Body ground
    LG-B - Body ground
    Front addition solenoid (-) RH output
    Approx. 1.5 seconds after turning power switch on (IG)
    Below 1.5 V
    A46-7 (SLAFR+) - Body ground
    LG - Body ground
    Front addition solenoid (+) RH output
    Brake pedal depressed approx. 1.5 seconds after turning power switch on (IG)
    Pulse generation
    (see waveform 1)
    A46-8 (E) - Body ground
    W - Body ground
    Pressure sensor ground
    Power switch off
    Below 1 Ω
    A46-9 (VCM1) - Body ground
    B - Body ground
    Pressure sensor power
    Power switch on (IG)
    4.75 to 5.25 V
    A46-11 (MR1+) - Body ground
    V - Body ground
    ABS motor relay power 1
    Approx. 1.5 seconds after turning power switch on (IG)
    8.8 to 14 V
    A46-12 (SR1) - Body ground
    L-R - Body ground
    ABS main relay output 1
    Approx. 1.5 seconds after turning power switch on (IG)
    Below 1 V
    A46-13 (SCSS) - Body ground
    BR - Body ground
    Stroke simulator cut solenoid output
    Brake pedal depressed approx. 1.5 seconds after turning power switch on (IG)
    Below 1.5 V
    A46-15 (SLARL+) - Body ground
    L - Body ground
    Rear addition solenoid (+) LH output
    Brake pedal depressed approx. 1.5 seconds after turning power switch on (IG)
    Pulse generation
    (see waveform 1)
    A46-16 (SLRRL+) - Body ground
    GR - Body ground
    Rear reduction solenoid (+) LH output
    Brake pedal depressed approx. 1.5 seconds after turning power switch on (IG)
    Pulse generation
    (see waveform 1)
    A46-17 (SLRFR+) - Body ground
    P - Body ground
    Front reduction solenoid (+) RH output
    Power switch on (IG), after approx. 1.5 seconds brake pedal depressed → released
    Pulse generation
    (see waveform 2)
    A46-18 (PRL) - Body ground
    W - Body ground
    Rear pressure sensor LH input
    Power switch on (IG), brake pedal released
    0.3 to 0.8 V
    A46-20 (SG1) - Body ground
    LG - Body ground
    Pressure sensor shield ground 1
    Power switch off
    Below 1 Ω
    A46-21 (PACC) - Body ground
    Y - Body ground
    Accumulator pressure sensor input
    Power switch on (IG), after pump motor operates and stops by pedal operation
    3.3 to 4.7 V
    A46-22 (FR+) - Body ground
    W - Body ground
    Front sensor (+) RH input
    Power switch off
    Below 1 Ω
    A46-23 (PFR) - Body ground
    L - Body ground
    Front pressure sensor RH input
    Power switch on (IG), brake pedal released
    0.3 to 0.8 V
    A46-25 (MR1) - Body ground
    LG - Body ground
    ABS motor relay output 1
    Power switch on (IG), pump motor is operating
    Below 1.5 V
    A46-26 (SLRRL-) - Body ground
    GR-R - Body ground
    Rear reduction solenoid (-) LH output
    Approx. 1.5 seconds after turning power switch on (IG)
    Below 1.5 V
    A46-27 (SLARL-) - Body ground
    Y - Body ground
    Rear addition solenoid (-) LH output
    Approx. 1.5 seconds after turning power switch on (IG)
    Below 1.5 V
    A46-29 (MTT) - Body ground
    L - Body ground
    Pump motor test input
    Power switch on (IG), pump motor is operating
    3.5 V or higher
    A46-30 (PMC1) - Body ground
    G - Body ground
    Master pressure sensor input 1
    Power switch on (IG), brake pedal released
    0.3 to 0.8 V
    A46-31 (PCK1) - Body ground
    BR - Body ground
    Pressure sensor check output 1
    Approx. 1.5 seconds after turning power switch on (IG)
    4.75 to 5.25 V
    A46-32 (FR-) - Body ground
    O - Body ground
    Front sensor (-) RH input
    Vehicle speed input
    Pulse generation
    (see waveform 3)
    A46-34 (SLRFR-) - Body ground
    P-B - Body ground
    Front reduction solenoid (-) RH output
    Approx. 1.5 seconds after turning power switch on (IG)
    Below 1.5 V
    A44-1 (GND3) - Body ground
    BR - Body ground
    Skid control ECU ground 3
    Always
    Below 1 Ω
    A44-2 (GND2) - Body ground
    W-B - Body ground
    Skid control ECU ground 2
    Always
    Below 1 Ω
    A44-3 (+BI1) - Body ground
    B - Body ground
    ABS main relay power input 1
    Power switch off
    11 to 14 V
    A44-5 (+BO1) - Body ground
    R - Body ground
    ABS main relay power output 1
    Power switch on (IG)
    8.8 to 14 V
    A44-7 (IG1) - Body ground
    Y - Body ground
    IG1 power
    Power switch on (IG)
    11 to 14 V
    A44-10 (RSS) - Body ground
    V - Body ground
    Speed sensor shield ground
    Power switch off
    Below 1 Ω
    A44-12 (BZ) - Body ground
    O - Body ground
    Skid control buzzer output
    Power switch on (IG), buzzer is operating
    Below 1 V
    A44-14 (STP) - Body ground
    L - Body ground
    Stop light switch signal input
    Stop light switch ON → OFF
    (Brake pedal depressed → released)
    8 to 14 V
    → Below 1.5 V
    A44-18 (CANL) - Body ground
    W - Body ground
    CAN communication
    (Send and receive-)
    Check DTC using the Techstream
    CAN communication's
    DTC is not output
    A44-19 (CANH) - Body ground
    B - Body ground
    CAN communication
    (Send and receive+)
    Check DTC using the Techstream
    CAN communication's
    DTC is not output
    A44-20 (FAIL) - Body ground
    L - Body ground
    Capacitor communication
    (Receive)
    Approx. 1.5 seconds after turning power switch on (IG)
    Pulse generation
    (see waveform 5)
    A44-22 (SP1) - Body ground
    BR - Body ground
    Speedometer output
    Vehicle speed input
    Pulse generation
    (see waveform 4)
    A44-27 (RL+) - Body ground
    R - Body ground
    Rear sensor (+) LH input
    Power switch off
    Below 1 Ω
    A44-30 (ENA) - Body ground
    Y - Body ground
    Capacitor communication
    (Send)
    Approx. 1.5 seconds after turning power switch on (IG)
    Pulse generation
    (see waveform 6)
    A44-32 (TS) - Body ground
    GR - Body ground
    Sensor diagnosis check input
    Power switch on (IG), connect terminals TS and CG of the DLC3 → disconnect
    Below 1.5 V
    → 9.1 to 13.6 V
    A44-33 (VBZ) - Body ground
    LG - Body ground
    Skid control buzzer power
    Power switch on (IG)
    9.1 to 13.6 V
    A44-35 (RL-) - Body ground
    G - Body ground
    Rear sensor (-) LH input
    Vehicle speed input
    Pulse generation
    (see waveform 3)
    A47-1 (GND5) - Body ground
    W-B - Body ground
    Skid control ECU ground 5
    Always
    Below 1 Ω
    A47-2 (GND4) - Body ground
    W-B - Body ground
    Skid control ECU ground 4
    Always
    Below 1 Ω
    A47-4 (+BO2) - Body ground
    W- Body ground
    ABS main relay power output 2
    Power switch on (IG)
    8.8 to 14 V
    A47-5 (+BI2) - Body ground
    GR - Body ground
    ABS main relay power input 2
    Power switch off
    11 to 14 V
    A47-6 (VCSK) - Body ground
    W - Body ground
    Stroke sensor power
    Power switch on (IG)
    3.75 to 4.95 V
    A47-7 (SSK) - Body ground
    Shielded - Body ground
    Stroke sensor shield ground
    Power switch off
    Below 1 Ω
    A47-8 (SKG) - Body ground
    R - Body ground
    Stroke sensor ground
    Power switch off
    Below 1 Ω
    A47-20 (SKS1) - Body ground
    G - Body ground
    Stroke sensor signal input 1
    Power switch on (IG), brake pedal released
    0.46 to 1.35 V
    A47-22 (SKS2) - Body ground
    B - Body ground
    Stroke sensor signal input 2
    Power switch on (IG), brake pedal released
    2.56 to 4.35 V
    A47-23 (RR-) - Body ground
    R - Body ground
    Rear sensor (-) RH input
    Power switch off
    Below 1 Ω
    A47-24 (EXI) - Body ground
    O - Body ground
    Stop light control relay input
    Stop light switch ON → OFF
    (Brake pedal depressed → released)
    8 to 14 V
    → Below 1.5 V
    A47-31 (RR+) - Body ground
    G - Body ground
    Rear sensor (+) RH input
    Vehicle speed input
    Pulse generation
    (see waveform 3)
    A45-1 (SLAFL+) - Body ground
    G-Y - Body ground
    Front addition solenoid (+) LH output
    Brake pedal depressed approx. 1.5 seconds after turning power switch on (IG)
    Pulse generation
    (see waveform 1)
    A45-2 (SLAFL-) - Body ground
    V - Body ground
    Front addition solenoid (-) LH output
    Approx. 1.5 seconds after turning power switch on (IG)
    Below 1.5 V
    A45-3 (SMC2) - Body ground
    B - Body ground
    Master cut solenoid 2 output
    Brake pedal depressed approx. 1.5 seconds after turning power switch on (IG)
    Below 1.5 V
    A45-4 (GND6) - Body ground
    W-B - Body ground
    Skid control ECU ground 6
    Always
    Below 1 Ω
    A45-5 (IG2) - Body ground
    W - Body ground
    IG2 power
    Power switch on (IG)
    11 to 14 V
    A45-6 (LBL) - Body ground
    B - Body ground
    Brake fluid level warning switch input
    Brake fluid level warning switch
    OFF → ON
    4 to 8 V
    → Below 1.5 V
    A45-7 (BS2) - Body ground
    BR - Body ground
    Battery source 2
    Approx. 1.5 seconds after turning power switch on (IG)
    8.8 to 14 V
    A45-8 (SLRFL+) - Body ground
    L - Body ground
    Front reduction solenoid (+) LH output
    Power switch on (IG), after approx. 1.5 seconds, brake pedal depressed → released
    Pulse generation
    (see waveform 2)
    A45-9 (SLARR-) - Body ground
    Y-R - Body ground
    Rear addition solenoid (-) RH output
    Approx. 1.5 seconds after turning power switch on (IG)
    Below 1.5 V
    A45-11 (CR) - Body ground
    P - Body ground
    Stop light control relay output
    Power switch on (IG)
    11 to 14 V
    A45-12 (SG2) - Body ground
    Shielded - Body ground
    Pressure sensor shield ground 2
    Power switch off
    Below 1 Ω
    A45-13 (FSS) - Body ground
    V - Body ground
    Speed sensor shield ground
    Power switch off
    Below 1 Ω
    A45-14 (VCM2) - Body ground
    BR - Body ground
    Pressure sensor power 2
    Power switch on (IG)
    4.75 to 5.25 V
    A45-15 (SR2) - Body ground
    O - Body ground
    ABS main relay output 2
    Approx. 1.5 seconds after turning power switch on (IG)
    Below 1 V
    A45-17 (R2+) - Body ground
    GR - Body ground
    ABS main relay power 2
    Power switch on (IG)
    9.1 to 13.6 V
    A45-18 (SLRRR-) - Body ground
    G-R - Body ground
    Rear reduction solenoid (-) RH output
    Approx. 1.5 seconds after turning power switch on (IG)
    Below 1.5 V
    A45-19 (SLARR+) - Body ground
    Y-G - Body ground
    Rear addition solenoid (+) RH output
    Brake pedal depressed approx. 1.5 seconds after turning power switch on (IG)
    Pulse generation
    (see waveform 1)
    A45-20 (SLRRR+) - Body ground
    G-O - Body ground
    Rear reduction solenoid (+) RH output
    Brake pedal depressed approx. 1.5 seconds after turning power switch on (IG)
    Pulse generation
    (see waveform 1)
    A45-21 (PCK2) - Body ground
    G - Body ground
    Pressure sensor check output 2
    Power switch on (IG)
    4.75 to 5.25 V
    A45-22 (FL+) - Body ground
    G - Body ground
    Front sensor (+) LH input
    Power switch off
    Below 1 Ω
    A45-23 (PFL) - Body ground
    R - Body ground
    Front pressure sensor LH input
    Power switch on (IG), brake pedal released
    0.3 to 0.8 V
    A45-25 (MR2+) - Body ground
    Y - Body ground
    ABS motor relay power 2
    Approx. 1.5 seconds after turning power switch on (IG)
    8.8 to 14 V
    A45-26 (SLRFL-) - Body ground
    L-W - Body ground
    Front reduction solenoid (-) LH output
    Approx. 1.5 seconds after turning power switch on (IG)
    Below 1.5 V
    A45-27 (PMC2) - Body ground
    L - Body ground
    Master pressure sensor input 2
    Power switch on (IG), brake pedal released
    0.3 to 0.8 V
    A45-28 (FL-) - Body ground
    R - Body ground
    Front sensor (-) LH input
    Vehicle speed input
    Pulse generation
    (see waveform 3)
    A45-29 (E2) - Body ground
    Y - Body ground
    Pressure sensor ground 2
    Power switch off
    Below 1 Ω
    A45-30 (MR2) - Body ground
    L - Body ground
    ABS motor relay output 2
    Power switch on (IG), pump motor is operating
    Below 1.5 V
    A45-31 (PRR) - Body ground
    W - Body ground
    Rear pressure sensor RH input
    Power switch on (IG), brake pedal released
    0.3 to 0.8 V



  4. C156526E01
  5. Waveform 1 (Reference): Using an oscilloscope:
    Item
    Condition
    Tool setting
    5 V/DIV., 200 ms./DIV.
    Vehicle condition
    1. While driving at approximately 20 km/h (12 mph)
    2. Brake pedal depressed

    HINT:
    Normal waveform is output only when BS1 and BS2 voltages are normal (11 to 14 V).



  6. C156526E01
  7. Waveform 2 (Reference): Using an oscilloscope:
    Item
    Condition
    Tool setting
    5 V/DIV., 200 ms./DIV.
    Vehicle condition
    1. While driving at approximately 20 km/h (12 mph)
    2. Brake pedal depressed → released

    HINT:
    Normal waveform is output only when BS1 and BS2 voltages are normal (11 to 14 V).



  8. C156524E01
  9. Waveform 3 (Reference): Using an oscilloscope:
    Item
    Condition
    Tool setting
    0.5 V/DIV., 2 ms./DIV.
    Vehicle condition
    While driving at approximately 30 km/h (18 mph)

    HINT:
    As the vehicle speed (tire rotating speed) becomes faster, the cycle becomes shorter and the output voltage higher.



  10. C156528E01
  11. Waveform 4 (Reference): Using an oscilloscope:
    Item
    Condition
    Tool setting
    5 V/DIV., 50 ms./DIV.
    Vehicle condition
    While driving at approximately 20 km/h (12 mph)

    HINT:
    As the vehicle speed (tire rotating speed) becomes faster, the cycle becomes shorter.



  12. C156529E01
  13. Waveform 5 (Reference): Using an oscilloscope:
    Item
    Condition
    Tool setting
    5 V/DIV., 200 ms./DIV.
    Vehicle condition
    Turn the power switch on (IG)



  14. C156529E01
  15. Waveform 6 (Reference): Using an oscilloscope:
    Item
    Condition
    Tool setting
    2 V/DIV., 100 ms./DIV.
    Vehicle condition
    Turn the power switch on (IG)