Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

ELECTRONICALLY CONTROLLED BRAKE SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the power switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the power switch on (IG).

  5. Turn the Techstream on.

  6. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

  7. According to the display on the Techstream, read the Data List.

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ABS Warning Light
    ABS warning light / ON or OFF
    ON: Warning light ON
    OFF: Warning light OFF
    -
    Brake Warning Light
    Brake warning light / red (malfunction) / ON or OFF
    ON: Warning light ON
    OFF: Warning light OFF
    -
    Slip Indicator Light
    Slip indicator light / ON or OFF
    ON: Indicator light ON
    OFF: Indicator light OFF
    -
    ECB* Warning Light
    Brake warning light / yellow (minor malfunction) / ON or OFF
    ON: Warning light ON
    OFF: Warning light OFF
    -
    Buzzer
    Skid control buzzer / ON or OFF
    ON: Buzzer ON
    OFF: Buzzer OFF
    -
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Parking Brake SW
    Parking brake switch / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -
    Reservoir Warning SW
    Brake fluid level warning switch / ON or OFF
    ON: Reservoir level low
    OFF: Reservoir level normal
    -
    Shift Lever Position
    Shift lever position information / P/N, R, D/M, 1st-6th/B, FAIL
    Actual shift lever position
    -
    Inspection Mode
    Inspection mode / OTHER or INSPECT
    OTHER: Normal mode
    INSPECT: Inspection mode
    -
    Master Cylinder Sensor
    Master cylinder pressure sensor 1 reading / min.: 0 V, max.: 5 V
    When brake pedal is released: 0.3 to 0.9 V
    Reading increases when brake pedal is depressed
    Voltage of M/C
    Voltage of master cylinder pressure sensor / min.: -2.5 V, max.: 2.49 V
    Min.: -2.5 V
    Max.: 2.49 V
    -
    Master Cylinder Sensor2
    Master cylinder pressure sensor 2 reading / min.: 0 V, max.: 5 V
    When brake pedal is released: 0.3 to 0.9 V
    Reading increases when brake pedal is depressed
    Voltage of M/C2
    Voltage of master cylinder pressure sensor 2 / min.: -2.5 V, max.: 2.49 V
    Min.: -2.5 V
    Max.: 2.49 V
    -
    Stroke Sensor
    Stroke sensor / min.: 0 V, max.: 5 V
    When brake pedal is released: 0.7 to 1.3 V
    -
    Voltage of Stroke Sensor
    Voltage of stroke sensor / min.: -2.5 V, max.: 2.49 V
    Min.: -2.5 V
    Max.: 2.49 V
    -
    Stroke Sensor2
    Stroke sensor 2 / min.: 0 V, max.: 5 V
    When brake pedal is released: 3.7 to 4.3 V
    -
    Voltage of Stroke Sensor2
    Voltage of stroke sensor 2 / min.: -2.5 V, max.: 2.49 V
    Min.: -2.5 V
    Max.: 2.49 V
    -
    Accumulator Sensor
    Accumulator pressure sensor / min.: 0 V, max.: 5 V
    Specified value: 3.3 to 4.7 V
    -
    Deceleration Sensor
    Acceleration sensor 1 reading / min.: -18.52 m/s2, max.: 18.39 m/s2
    Min.: -18.52 m/s2
    Max.: 18.39 m/s2
    Reading changes when vehicle is bounced
    Zero Point of Decele
    Memorized zero value / min.: -25.11 m/s2, max.: 24.91 m/s2
    Min.: -25.11 m/s2
    Max.: 24.91 m/s2
    -
    Deceleration Sensor2
    Acceleration sensor 2 reading / min.: -18.52 m/s2, max.: 18.39 m/s2
    Min.: -18.52 m/s2
    Max.: 18.39 m/s2
    Reading changes when vehicle is bounced
    Zero Point of Decele2
    Memorized zero value / min.: -25.11 m/s2, max.: 24.91 m/s2
    Min.: -25.11 m/s2
    Max.: 24.91 m/s2
    -
    Yaw Rate Sensor
    Yaw rate sensor 1 / min.: -128 degrees/sec., max.: 127 degrees/sec.
    Vehicle stationary: 0 degrees/sec.
    Right turn: -128 to 0 degrees/sec.
    Left turn: 0 to 127 degrees/sec.
    -
    Zero Point of Yaw Rate
    Memorized zero value / min.: -128 degrees/sec., max.: 127 degrees/sec.
    Min.: -128 degrees/sec.
    Max.: 127 degrees/sec.
    -
    Yaw Rate Sensor2
    Yaw rate sensor 2 / min.: -128 degrees/sec., max.: 127 degrees/sec.
    Vehicle stationary: 0 degrees/sec.
    Right turn: -128 to 0 degrees/sec.
    Left turn: 0 to 127 degrees/sec.
    -
    Zero Point of Yaw Rate2
    Memorized zero value / min.: -128 degrees/sec., max.: 127 degrees/sec.
    Min.: -128 degrees/sec.
    Max.: 127 degrees/sec.
    -
    Steering Angle Sensor
    Steering angle sensor / min.: -3276.8 degrees, max.: 3276.7 degrees
    Left turn: Increase
    Right turn: Decrease
    -
    Zero Point of Steering Angle
    Memorized zero value / min.: -3276.8 degrees, max.: 3276.7 degrees
    Min.: -3276.8 degrees
    Max.: 3276.7 degrees
    -
    FR W/C Sensor
    FR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V
    When brake pedal is released: 0.3 to 0.9 V
    -
    FL W/C Sensor
    FL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V
    When brake pedal is released: 0.3 to 0.9 V
    -
    RR W/C Sensor
    RR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V
    When brake pedal is released: 0.3 to 0.9 V
    -
    RL W/C Sensor
    RL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V
    When brake pedal is released: 0.3 to 0.9 V
    -
    Lateral G
    Lateral G / min.: -25.11 m/s2, max.: 24.91 m/s2
    Min.: -25.11 m/s2
    Max.: 24.91 m/s2
    -
    Forward and Rearward G
    Forward and backward G / min.: -25.11 m/s2, max.: 24.91 m/s2
    Min.: -25.11 m/s2
    Max.: 24.91 m/s2
    -
    Yaw Rate Value
    Yaw rate value / min.: -128 degrees/sec., max.: 127 degrees/sec.
    Min.: -128 degrees/sec.
    Max.: 127 degrees/sec.
    -
    Steering Angle Value
    Steering angle value / min.: -3276.8 degrees, max.: 3276.7 degrees
    Min.: -3276.8 degrees
    Max.: 3276.7 degrees
    -
    Stop Light Relay
    Stop light control relay / ON or OFF
    ON: Relay ON
    OFF: Relay OFF
    -
    FR Wheel Speed
    FR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer
    FL Wheel Speed
    FL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer
    RR Wheel Speed
    RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer
    RL Wheel Speed
    RL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer
    Vehicle Speed
    Maximum wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph)
    Actual vehicle speed
    Speed indicated on speedometer
    FR Wheel Acceleration
    FR wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
    Min.: -200.84 m/s2
    Max.: 199.27 m/s2
    -
    FL Wheel Acceleration
    FL wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
    Min.: -200.84 m/s2
    Max.: 199.27 m/s2
    -
    RR Wheel Acceleration
    RR wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
    Min.: -200.84 m/s2
    Max.: 199.27 m/s2
    -
    RL Wheel Acceleration
    RL wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
    Min.: -200.84 m/s2
    Max.: 199.27 m/s2
    -
    Stop Light Relay Output
    Stop light control relay output / ON or OFF
    ON: Relay output ON
    OFF: Relay output OFF
    -
    FR Wheel ABS Ctrl Status
    FR wheel ABS control status / ON or OFF
    ON: During the control
    -
    FL Wheel ABS Ctrl Status
    FL wheel ABS control status / ON or OFF
    ON: During the control
    -
    RR Wheel ABS Ctrl Status
    RR wheel ABS control status / ON or OFF
    ON: During the control
    -
    RL Wheel ABS Ctrl Status
    RL wheel ABS control status / ON or OFF
    ON: During the control
    -
    BA Ctrl Status
    BA control status / ON or OFF
    ON: During the control
    -
    TRC(TRAC) Ctrl Status
    TRAC control status / ON or OFF
    ON: During the control
    -
    TRC(TRAC) Brake Ctrl Status
    TRAC brake control status / ON or OFF
    ON: During the control
    -
    FR Wheel VSC Ctrl Status
    FR wheel VSC control status / ON or OFF
    ON: During the control
    -
    FL Wheel VSC Ctrl Status
    FL wheel VSC control status / ON or OFF
    ON: During the control
    -
    RR Wheel VSC Ctrl Status
    RR wheel VSC control status / ON or OFF
    ON: During the control
    -
    RL Wheel VSC Ctrl Status
    RL wheel VSC control status / ON or OFF
    ON: During the control
    -
    Accelerator Opening Angle %
    The difference of a present accelerator / min.: 0%, max.: 128%
    Min.: 0%
    Max.: 128%
    -
    FR Regenerative Request
    FR regenerative request torque / min.: 0 N*m, max.: 65536 N*m
    Min.: 0 N*m
    Max.: 65536 N*m
    -
    FR Regenerative Operation
    FR regenerative operation torque / min.: 0 N*m, max.: 65536 N*m
    Min.: 0 N*m
    Max.: 65536 N*m
    -
    RR Regenerative Request
    RR regenerative request torque / min.: 0 N*m, max.: 65536 N*m
    Min.: 0 N*m
    Max.: 65536 N*m
    -
    RR Regenerative Operation
    RR regenerative operation torque / min.: 0 N*m, max.: 65536 N*m
    Min.: 0 N*m
    Max.: 65536 N*m
    -
    Regenerative Cooperation
    Regenerative cooperation / ON or OFF
    ON: Operate
    OFF: Not operate
    -
    ECB* Motor Relay
    ABS motor relay / ON or OFF
    ON: Motor relay ON
    OFF: Motor relay OFF
    -
    ECB* Motor Relay2
    ABS motor relay 2 / ON or OFF
    ON: Motor relay ON
    OFF: Motor relay OFF
    -
    ECB* Main Relay
    ABS main relay / ON or OFF
    ON: Main relay ON
    OFF: Main relay OFF
    -
    ECB* Main Relay2
    ABS main relay 2 / ON or OFF
    ON: Main relay ON
    OFF: Main relay OFF
    -
    ECB* Solenoid (SMC1)
    Master cut solenoid (SMC1) / ON or OFF
    ON: Operate
    OFF: Not operate
    -
    ECB* Solenoid (SMC2)
    Master cut solenoid (SMC2) / ON or OFF
    ON: Operate
    OFF: Not operate
    -
    ECB* Solenoid (SCSS)
    Stroke simulator solenoid (SCSS) / ON or OFF
    ON: Operate
    OFF: Not operate
    -
    SLAFR Solenoid Current
    Linear solenoid (SLAFR) current / min.: 0 A, max.: 3 A
    When brake pedal is released: 0 A
    -
    SLAFL Solenoid Current
    Linear solenoid (SLAFL) current / min.: 0 A, max.: 3 A
    When brake pedal is released: 0 A
    -
    SLARR Solenoid Current
    Linear solenoid (SLARR) current / min.: 0 A, max.: 3 A
    When brake pedal is released: 0 A
    -
    SLARL Solenoid Current
    Linear solenoid (SLARL) current / min.: 0 A, max.: 3 A
    When brake pedal is released: 0 A
    -
    SLRFR Solenoid Current
    Linear solenoid (SLRFR) current / min.: 0 A, max.: 3 A
    When brake pedal is released: 0 A
    -
    SLRFL Solenoid Current
    Linear solenoid (SLRFL) current / min.: 0 A, max.: 3 A
    When brake pedal is released: 0 A
    -
    SLRRR Solenoid Current
    Linear solenoid (SLRRR) current / min.: 0 A, max.: 3 A
    When brake pedal is released: 0 A
    -
    SLRRL Solenoid Current
    Linear solenoid (SLRRL) current / min.: 0 A, max.: 3 A
    When brake pedal is released: 0 A
    -
    FR Speed Open
    FR speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    FL Speed Open
    FL speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    RR Speed Open
    RR speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    RL Speed Open
    RL speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Yaw Rate Open
    Yaw rate sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Deceleration Open
    Acceleration sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Steering Open
    Steering angle sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Master Cylinder Open
    Master cylinder pressure sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Master Cylinder2 Open
    Master cylinder pressure sensor 2 open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Stroke Open
    Stroke sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    FR Wheel Cylinder Open
    FR wheel cylinder pressure sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    FL Wheel Cylinder Open
    FL wheel cylinder pressure sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    RR Wheel Cylinder Open
    RR wheel cylinder pressure sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    RL Wheel Cylinder Open
    RL wheel cylinder pressure sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Accumulator Open
    Accumulator pressure sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    HV Communication Open
    Hybrid vehicle communication open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Number of DTC
    Number of DTC / min.: 0, max.: 255
    Min.: 0
    Max.: 255
    -
    *: Electronically Controlled Brake System


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts to operate without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the power switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the power switch on (IG).

  5. Turn the Techstream on.

  6. Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.

  7. According to the display on the Techstream, perform the Active Test.

    ABS / VSC / TRAC: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ABS Warning Light
    ABS warning light
    Warning light ON / OFF
    Observe combination meter
    Brake Warning Light
    Brake warning light / red (malfunction)
    Warning light ON / OFF
    Observe combination meter
    Slip Indicator Light
    Slip indicator light
    Indicator light ON / OFF
    Observe combination meter
    ECB* Warning Light
    Brake warning light / yellow (minor malfunction)
    Warning light ON / OFF
    Observe combination meter
    Buzzer
    Skid control buzzer
    Buzzer ON / OFF
    Buzzer can be heard
    Stop Light Relay
    Stop light control relay
    Relay ON / OFF
    Stop lights come on
    ECB* Main Relay
    ABS main relay
    Relay ON / OFF
    Operation sound of relay (clicking sound) can be heard
    ECB* Main Relay2
    ABS main relay 2
    Relay ON / OFF
    Operation sound of relay (clicking sound) can be heard
    ECB* Motor Relay
    ABS motor relay
    Relay ON / OFF
    Operation sound of relay (clicking sound) and motor can be heard
    ECB* Motor Relay2
    ABS motor relay 2
    Relay ON / OFF
    Operation sound of relay (clicking sound) and motor can be heard
    ECB* Solenoid (SMC1)
    Master cut solenoid (SMC1)
    Solenoid ON / OFF
    Operation sound of solenoid (clicking sound) can be heard
    ECB* Solenoid (SMC2)
    Master cut solenoid (SMC2)
    Solenoid ON / OFF
    Operation sound of solenoid (clicking sound) can be heard
    ECB* Control Invalid
    Electronically controlled brake system control invalid
    Control invalid ON / OFF
    Electronically controlled brake system control is disabled (braking with no accumulator assist)
    Accumulator Zero Down
    Accumulator zero down activation
    Activation ON / OFF
    Brake fluid in the accumulator makes noise
    Stroke Simulator Cut Valve Pattern
    Stroke simulator cut valve pattern activation
    Activation ON / OFF
    -
    (Difficult to identify visually)
    Actuator Air Bleeding Pattern
    Actuator air bleeding pattern activation
    Activation ON / OFF
    When accumulator pressure lowers, pump operation creates sound
    Power Supply Air Bleeding Pattern1
    Power supply air bleeding pattern activation 1
    Activation ON / OFF
    When accumulator pressure lowers, pump operation creates sound
    Power Supply Air Bleeding Pattern2
    Power supply air bleeding pattern activation 2
    Activation ON / OFF
    When accumulator pressure lowers, pump operation creates sound
    RL Wheel Air Bleeding Pattern
    RL wheel air bleeding pattern activation
    Activation ON / OFF
    When accumulator pressure lowers, pump operation creates sound
    RR Wheel Air Bleeding Pattern
    RR wheel air bleeding pattern activation
    Activation ON / OFF
    When accumulator pressure lowers, pump operation creates sound
    Pump Check Pattern
    Pump check pattern activation
    Activation ON / OFF
    When accumulator pressure lowers, pump operation creates sound
    Drain System Air Bleeding Pattern
    Drain system air bleeding pattern activation
    Activation ON / OFF
    When accumulator pressure lowers, pump operation creates sound
    ECB* Solenoid (SLRRL) Value Close
    Linear solenoid (SLRRL) valve
    Valve close ON / OFF
    -
    ECB* Solenoid (SLARL) Value Close
    Linear solenoid (SLARL) valve
    Valve close ON / OFF
    -
    ECB* Solenoid (SLRRR) Value Close
    Linear solenoid (SLRRR) valve
    Valve close ON / OFF
    -
    ECB* Solenoid (SLARR) Value Close
    Linear solenoid (SLARR) valve
    Valve close ON / OFF
    -
    ECB* Solenoid (SLRFL) Value Close
    Linear solenoid (SLRFL) valve
    Valve close ON / OFF
    -
    ECB* Solenoid (SLAFL) Value Close
    Linear solenoid (SLAFL) valve
    Valve close ON / OFF
    -
    ECB* Solenoid (SLRFR) Value Close
    Linear solenoid (SLRFR) valve
    Valve close ON / OFF
    -
    ECB* Solenoid (SLAFR) Value Close
    Linear solenoid (SLAFR) valve
    Valve close ON / OFF
    -
    *: Electronically Controlled Brake System