Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

ELECTRONICALLY CONTROLLED BRAKE SYSTEM > FREEZE FRAME DATA

for Preparation Click here



FREEZE FRAME DATA/INFORMATION
  1. Whenever an ABS, VSC, electronically controlled brake system DTC is detected, the skid control ECU stores the current vehicle (sensor) state as Freeze Frame Data.

  2. The skid control ECU stores the number of times (maximum: 31) the power switch has been turned from off to on (IG) since the last time the ABS was activated.

  3. For DTCs stored in the skid control ECU, information (INF) codes that are contained in the Freeze Frame Data can be displayed on the Techstream.

    HINT:
    1. However, if the vehicle is stopped or at a low speed (7 km/h (4.3 mph) or less), or if a DTC is detected, the skid control ECU will stop counting the number of times the power switch had been turned from off to on (IG).
    2. Freeze Frame Data at the time the ABS operates:
      The skid control ECU stores and updates data whenever the ABS system operates.
      When the ECU stores data at the time a DTC is detected, the data stored during ABS operation is erased.
    3. Freeze Frame Data at the time a DTC is detected:
      When the skid control ECU stores data at the time a DTC is detected, no updates will be performed until the data is cleared.


CHECK FREEZE FRAME DATA AND INFORMATION
  1. Connect the Techstream to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the Techstream on.

  4. Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.

  5. According to the display on the Techstream, select the trouble code data display with Freeze Frame Data.

  6. Read the Freeze Frame Data recorded when the DTC was set.

  7. Read the information.

    1. Select the item that has an information (INF) code from the Freeze Frame Data screen.

      ABS / VSC / TRAC: 
      Tester Display
      Measurement Item
      Reference Value
      Detailed Freeze DTC
      Detailed code for Freeze Frame DTC
      Min.: 0, Max.: 65535
      Elapsed Time after Freeze Trigger
      Elapsed time after freeze trigger
      Min.: 0 ms, Max.: 500 ms
      Number of IG ON
      Number of operations of power switch on (IG) after storing Freeze Frame Data
      0 to 31
      Elapsed Time
      Elapsed time after power switch on (IG)
      Min.: 0 sec., Max.: 100661.76 sec.
      Buzzer
      Skid control buzzer signal
      Skid control buzzer ON: ON, OFF: OFF
      Stop Light SW
      Stop light switch signal
      Stop light switch ON: ON, OFF: OFF
      Parking Brake SW
      Parking brake switch signal
      Parking brake switch ON: ON, OFF: OFF
      Reservoir Warning SW
      Brake fluid level warning switch signal
      Brake fluid level warning switch ON: ON, OFF: OFF
      Gear Position
      Gear position information
      FAIL
      1st
      2nd
      3rd
      4th
      5th
      6th
      P, N
      R
      NOT R
      Shift Lever Position
      Shift lever position information
      FAIL
      1st
      2nd
      3rd
      4th
      5th
      6th/B
      D/M
      P, N
      R
      Operated System
      Operated system status
      ABS: ABS activated
      VSC: VSC activated
      TRC: TRAC activated
      BA: BA activated
      HA-CTRL: Hill-start assist control activated
      FAIL: Fail safe mode activated
      NON: No system activated
      SYS: System prohibited
      Master Cylinder Sensor
      Master cylinder pressure sensor reading
      Brake pedal released: 0.3 to 0.9 V
      M/C Sensor Grade
      Master cylinder pressure sensor change
      Min.: -30 MPa/s, Max.: 225 MPa/s
      Master Cylinder Sensor2
      Master cylinder pressure sensor reading
      Brake pedal released: 0.3 to 0.9 V
      Stroke Sensor
      Stroke sensor reading
      Min.: 0 V, Max.: 5 V
      Stroke Sensor2
      Stroke sensor 2 reading
      Min.: 0 V, Max.: 5 V
      Accumulator Sensor
      Accumulator pressure sensor reading
      Min.: 0 V, Max.: 5 V
      Yaw Rate Sensor
      Yaw rate sensor reading
      Min.: -128 deg/s, Max.: 127 deg/s
      FR W/C Sensor
      FR wheel cylinder pressure sensor reading
      Min.: 0 V, Max.: 5 V
      FL W/C Sensor
      FL wheel cylinder pressure sensor reading
      Min.: 0 V, Max.: 5 V
      RR W/C Sensor
      RR wheel cylinder pressure sensor reading
      Min.: 0 V, Max.: 5 V
      RL W/C Sensor
      RL wheel cylinder pressure sensor reading
      Min.: 0 V, Max.: 5 V
      Lateral G
      Lateral G
      Min.: -25.11 m/s2, Max.: 24.91 m/s2
      Forward and Rearward G
      Forward and backward G
      Min.: -25.11 m/s2, Max.: 24.91 m/s2
      FR Wheel Speed
      FR wheel speed
      Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
      FL Wheel Speed
      FL wheel speed
      Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
      RR Wheel Speed
      RR wheel speed
      Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
      RL Wheel Speed
      RL wheel speed
      Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
      Vehicle Speed
      Vehicle speed reading
      Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
      ECB* Motor Relay
      ABS motor relay signal
      ABS motor relay ON: ON, OFF: OFF
      ECB* Motor Relay2
      ABS motor relay 2 signal
      ABS motor relay 2 ON: ON, OFF: OFF
      ECB* Main Relay
      ABS main relay signal
      ABS main relay ON: ON, OFF: OFF
      ECB* Main Relay2
      ABS main relay 2 signal
      ABS main relay 2 ON: ON, OFF: OFF
      ECB* Solenoid (SMC1)
      Master cut solenoid (SMC1) signal
      Master cut solenoid (SMC1) ON: ON, OFF: OFF
      ECB* Solenoid (SMC2)
      Master cut solenoid (SMC2) signal
      Master cut solenoid (SMC2) ON: ON, OFF: OFF
      ECB* Solenoid (SCSS)
      Stroke simulator solenoid (SCSS) signal
      Stroke simulator solenoid (SCSS) ON: ON, OFF: OFF
      Capacitor Mode
      Capacitor mode
      Capacitor mode ON: ON, OFF: OFF
      IG1 Voltage Value
      IG1 voltage value
      Min.: 0 V, Max.: 20 V
      IG2 Voltage Value
      IG2 voltage value
      Min.: 0 V, Max.: 20 V
      BS1 Voltage Value
      BS1 voltage value
      Min.: 0 V, Max.: 20 V
      BS2 Voltage Value
      BS2 voltage value
      Min.: 0 V, Max.: 20 V
      VM1 Voltage Value
      VM1 voltage value
      Min.: 0 V, Max.: 20 V
      VM2 Voltage Value
      VM2 voltage value
      Min.: 0 V, Max.: 20 V
      +B1 Voltage Value
      +B1 voltage value
      Min.: 0 V, Max.: 20 V
      +B2 Voltage Value
      +B2 voltage value
      Min.: 0 V, Max.: 20 V
      Motor Relay Voltage Value
      Motor relay voltage value
      Min.: 0 V, Max.: 20 V
      SLAFR Solenoid Current
      Linear solenoid (SLAFR) current
      Min.: 0 A, Max.: 1.5 A
      SLAFL Solenoid Current
      Linear solenoid (SLAFL) current
      Min.: 0 A, Max.: 1.5 A
      SLARR Solenoid Current
      Linear solenoid (SLARR) current
      Min.: 0 A, Max.: 1.5 A
      SLARL Solenoid Current
      Linear solenoid (SLARL) current
      Min.: 0 A, Max.: 1.5 A
      SLRFR Solenoid Current
      Linear solenoid (SLRFR) current
      Min.: 0 A, Max.: 1.5 A
      SLRFL Solenoid Current
      Linear solenoid (SLRFL) current
      Min.: 0 A, Max.: 1.5 A
      SLRRR Solenoid Current
      Linear solenoid (SLRRR) current
      Min.: 0 A, Max.: 1.5 A
      SLRRL Solenoid Current
      Linear solenoid (SLRRL) current
      Min.: 0 A, Max.: 1.5 A
      FR Target Oil Pressure
      FR wheel target hydraulic pressure reading
      Min.: 0 MPa, Max.: 20 MPa
      FL Target Oil Pressure
      FL wheel target hydraulic pressure reading
      Min.: 0 MPa, Max.: 20 MPa
      RR Target Oil Pressure
      RR wheel target hydraulic pressure reading
      Min.: 0 MPa, Max.: 20 MPa
      RL Target Oil Pressure
      RL wheel target hydraulic pressure reading
      Min.: 0 MPa, Max.: 20 MPa
      Inspection Mode
      Inspection mode
      OTHER: Normal mode
      INSPECT: Inspection mode
      *: Electronically Controlled Brake System


CLEAR FREEZE FRAME DATA AND INFORMATION

NOTICE:
Clearing the DTCs will also clear the Freeze Frame Data and information (INF) codes.

  1. Connect the Techstream to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the Techstream on.

  4. Clear the DTCs and Freeze Frame Data (Click here).