Home › ENGINE › 3MZ-FE STARTING › SMART KEY SYSTEM

SMART KEY SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

B112605E17

  1. Disconnect the D7, D8, D9, 1E, 1F and 1M connectors.

  2. Measure the voltage and resistance of the wire harness side connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D8-6 (AM1) - Body ground
    GR - Body ground
    +B power supply
    Always
    11 to 14 V
    D7-1 (AM2) - Body ground
    B - Body ground
    +B power supply
    Always
    11 to 14 V
    D8-16 (SSW2) - Body ground
    BR - Body ground
    Power switch signal
    Power switch pushed
    Below 1 Ω
    D8-16 (SSW2) - Body ground
    BR - Body ground
    Power switch signal
    Power switch not pushed
    10 kΩ or higher
    D8-17 (SSW1) - Body ground
    P - Body ground
    Power switch signal
    Power switch pushed
    Below 1 Ω
    D8-17 (SSW1) - Body ground
    P - Body ground
    Power switch signal
    Power switch not pushed
    10 kΩ or higher
    1M-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    D9-5 (CANH) - Body ground
    B - Body ground
    CAN Line
    Always
    10 kΩ or higher
    D9-6 (CANL) - Body ground
    W - Body ground
    CAN Line
    Always
    10 kΩ or higher
    D9-15 (CANN) - Body ground*1
    W - Body ground
    CAN Line
    Always
    10 kΩ or higher
    D9-16 (CANP) - Body ground*1
    B - Body ground
    CAN Line
    Always
    10 kΩ or higher
    1F-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1E-7 (LIN1) - Body ground
    R - Body ground
    LIN line
    Always
    10 kΩ or higher

    HINT:
    *1: w/ Power back door

    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the connectors.

  4. Measure the voltage of the connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D7-11 (IG2D) - 1M-9 (GND2)
    Y - W-B
    IG2 signal
    Power switch on (IG)
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    D7-11 (IG2D) - 1M-9 (GND2)
    Y - W-B
    IG2 signal
    Power switch on (ACC)
    Below 1 V
    D8-3 (IG1D) - 1M-9 (GND2)
    SB - W-B
    IG1 signal
    Power switch on (IG)
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    D8-3 (IG1D) - 1M-9 (GND2)
    SB - W-B
    IG1 signal
    Power switch on (ACC)
    Below 1 V
    D8-18 (SLP) - 1M-9 (GND2)
    O - W-B
    Steering lock actuator position signal
    Steering lock is locked
    Pulse generation
    (See waveform 3)
    D8-18 (SLP) - 1M-9 (GND2)
    O - W-B
    Steering lock actuator position signal
    Steering lock is released
    Pulse generation
    (See waveform 3)
    D8-19 (SLR+) - 1M-9 (GND2)
    Y - W-B
    Steering lock motor signal
    Steering lock motor operating
    Below 1 V
    D8-19 (SLR+) - 1M-9 (GND2)
    Y - W-B
    Steering lock motor signal
    Steering lock motor does not operate
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    D8-22 (ACCD) - 1M-9 (GND2)
    GR - W-B
    ACC signal
    Power switch on (ACC)
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    D8-22 (ACCD) - 1M-9 (GND2)
    GR - W-B
    ACC signal
    Power switch off
    Below 1 V
    D8-25 (SWIL) - 1M-9 (GND2)
    R - W-B
    Illumination signal
    Light control switch TAIL or HEAD
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    D9-8 (RDY) - 1M-9 (GND2)
    O - W-B
    Tachometer signal
    Power switch on (READY)
    Pulse generation
    (See waveform 2)
    D9-9 (SPD) - 1M-9 (GND2)
    R - W-B
    Vehicle speed signal
    Power switch on (IG), rotate rear wheel slowly
    Pulse generation
    (See waveform 1)
    D10-4 (STSW) - 1M-9 (GND2)
    Y - W-B
    Hybrid control system activation request signal
    Brake pedal depressed, power switch held on (ST)
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    1F-2 (ACC) - Body ground
    SB - Body ground
    ACC power supply
    Always
    11 to 14 V
    1A-1 (IG) - Body ground
    B - Body ground
    IG power supply
    Always
    11 to 14 V
    1M-7 (STP) - 1M-9 (GND2)
    GR - W-B
    Stop light signal
    Brake pedal depressed
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    1M-7 (STP) - 1M-9 (GND2)
    GR - W-B
    Stop light signal
    Brake pedal released
    Below 1 V



  5. Using an oscilloscope, check the signal waveform of the ECU.



      I042329E01
    1. Waveform 1
      Waveform 1 (Reference): 
      Terminal No.
      D9-9 (SPD) - 1M-9 (GND2)
      Tool Setting
      5 V/DIV., 10 ms./DIV.
      Vehicle Condition
      Driving at approx. 20 km/h (12 mph)

      HINT:
      As the vehicle speed increases, the wavelength shortens.



    2. C165582E04
    3. Waveform 2
      Waveform 2 (Reference): 
      Terminal No.
      D9-8 (RDY) - 1M-9 (GND2)
      Tool Setting
      10 V/DIV., 10 ms./DIV.
      Vehicle Condition
      Power switch on (IG) or on (READY)



    4. A130277E01
    5. Waveform 3
      Waveform 3 (Reference): 
      Terminal No.
      D8-18 (SLP) - 1M-9 (GND2)
      Tool Setting
      2 V/DIV., 100 ms./DIV.
      Vehicle Condition
      Steering lock/unlock


CHECK CERTIFICATION ECU

B178888E02

  1. Disconnect the D40 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D40-1 (+B) - Body ground
    B - Body ground
    +B power supply
    Always
    11 to 14 V
    D40-10 (LIN) - Body ground
    L - Body ground
    LIN line
    Always
    10 kΩ or higher
    D40-17 (E) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the ECU connector.

  4. Measure the voltage of the connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D40-18 (IG) - Body ground
    G - Body ground
    Ignition power supply
    Power switch on (IG)
    11 to 14 V
    D40-18 (IG) - Body ground
    G - Body ground
    Ignition power supply
    Power switch off
    Below 1 V
    If the result is not as specified, the ECU may have a malfunction.


CHECK HYBRID VEHICLE CONTROL ECU

A103802E35

  1. Disconnect the A43, B1, B2, B3 and D35 hybrid vehicle control ECU connectors.

  2. Measure the voltage and resistance of the wire harness side connectors.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A43-1 (+B2) - Body ground
    Y - Body ground
    Power source of hybrid vehicle control ECU
    Power switch on (IG)
    11 to 14 V
    A43-2 (+B1) - Body ground
    GR - Body ground
    Power source of hybrid vehicle control ECU
    Power switch on (IG)
    11 to 14 V
    D35-9 (IGSW) - Body ground
    G - Body ground
    Power switch signal
    Power switch on (IG)
    11 to 14 V
    B3-4 (ME01) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B1-6 (E02) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B1-7 (E01) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B2-6 (E04) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B2-5 (E05) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B3-5 (E1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B3-7 (E03) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the hybrid vehicle control ECU connectors.

  4. Measure the voltage of the connectors.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D35-12 (RDY) - B3-5 (E1)
    O - W-B
    on (READY) signal (output)
    Power switch on (READY)
    Pulse generation (see waveform 1)
    D35-20 (ST2) - B3-5 (E1)
    Y - W-B
    Starter signal
    Power switch on (IG)
    0 to 1.5 V
    D35-31 (STP) - B3-5 (E1)
    R - W-B
    Stop light switch signal (input)
    Brake pedal depressed
    7.5 to 14 V
    D35-31 (STP) - B3-5 (E1)
    R - W-B
    Stop light switch signal (input)
    Brake pedal released
    Below 1.5 V

    HINT:
    *1: Voltage is output only when the engine is cranking.

    If the result is not as specified, the hybrid vehicle control ECU may have a malfunction.



  5. C165582E03
  6. Using an oscilloscope, check the signal waveform of the hybrid vehicle control ECU.
    Waveform 1 (Reference): 
    Terminal No.
    D35-12 (RDY) - B3-5 (E1)
    Tool Setting
    10 V/DIV., 10 ms./DIV.
    Vehicle Condition
    Power switch on (IG) or on (READY)

    HINT:
    As the vehicle speed increases, the wavelength shortens.


CHECK STEERING LOCK ECU

B118684E10

  1. Disconnect the D11 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D11-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    D11-2 (SGND) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 Ω
    D11-6 (IG2) - Body ground
    V - Body ground
    Ignition power supply
    Power switch on (IG)
    11 to 14 V
    D11-6 (IG2) - Body ground
    V - Body ground
    Ignition power supply
    Power switch off
    Below 1 V
    D11-7 (B) - Body ground
    G - Body ground
    +B power supply
    Always
    11 to 14 V

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D11 ECU connector.

  4. Measure the voltage of the connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D11-4 (SLP1) - D11-1 (GND)
    O - W-B
    Steering lock actuator position signal
    Steering is locked
    11 to 14 V
    D11-4 (SLP1) - D11-1 (GND)
    O - W-B
    Steering lock actuator position signal
    Steering is released
    Below 1 V

    1. If the result is not as specified, the ECU may have a malfunction.