Home › ENGINE › 3MZ-FE STARTING › SMART KEY SYSTEM

SMART KEY SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the DATA LIST information early in troubleshooting is one way to save diagnostic time.

  1. Connect Techstream to the DLC3.
    When using Techstream with the power switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 or less second intervals until communication between the tester and vehicle starts.

  2. Turn the power switch on (IG).

  3. Read the DATA LIST.

    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ACC SW
    Power switch on (ACC) / ON or OFF
    ON: Power switch on (ACC)
    OFF: Power switch off
    -
    IG SW
    Power switch on (IG) / ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    -
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Start Switch1
    Start switch 1 / ON or OFF
    ON: Power switch is pushed
    OFF: Power switch is not pushed
    -
    Start Switch2
    Start switch 2 / ON or OFF
    ON: Power switch is pushed
    OFF: Power switch is not pushed
    -
    Steering Unlock Switch
    Steering lock condition / ON or OFF
    ON: Steering is unlocked (Power switch on (ACC))
    OFF: Steering is locked (Power switch off)
    -
    Shift P Signal
    Shift P position signal / ON or OFF
    ON: Shift position is P
    OFF: Shift position is not P
    -
    Vehicle Speed Signal
    Vehicle speed signal / Stop or Run
    Stop: Vehicle is stopped
    Run: Vehicle is running
    -
    IG1 Relay Monitor (Outside)
    IG1 relay monitor (outer) / ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    -
    IG2 Relay Monitor (Outside)
    IG2 relay monitor (outer) / ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    -
    IG1 Relay Monitor (Inside)
    IG1 relay monitor (inner) / ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    -
    IG2 Relay Monitor (Inside)
    IG2 relay monitor (inner) / ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    -
    ACC Relay Monitor
    ACC relay monitor / ON or OFF
    ON: Power switch on (ACC)
    OFF: Power switch off
    -
    Latch Circuit
    Latch circuit / ON or OFF
    ON: Power switch on (IG) or on (READY)
    OFF: Power switch off or on (ACC)
    -
    Starter Request Signal
    Hybrid control system start request signal / ON or OFF
    ON: STSW signal is ON
    OFF: STSW signal is OFF
    -
    Power Supply Condition
    Power supply condition / All, ACC ON, IG1 IG2, ST ON
    All: All relays are OFF
    ACC ON: ACC relay is ON
    IG1: IG1 relay is ON
    IG2: IG2 relay is ON
    ST ON: ST request signal is ON
    -
    Ready Signal
    Hybrid control system start request signal monitor / ON or OFF
    ON: System is ON (READY)
    OFF: System is OFF
    Power switch pressed and held with shift lever in P
    Communication Smart/Wireless
    Communication for certification ECU (smart key ECU assembly) / OK or STOP
    OK: Communication
    STOP: No communication
    -


PERFORM ACTIVE TEST

HINT:
Using Techstream to perform ACTIVE TEST allows the relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing the ACTIVE TEST early in troubleshooting is one way to save diagnostic time. The DATA LIST can be displayed while performing ACTIVE TESTs.

  1. Connect Techstream to the DLC3.

  2. Turn the power switch on (IG).

  3. Perform the ACTIVE TEST according to the display on the tester.


Main Body: 
Tester Display
Test Part
Control Range
Diagnostic Note
Indicator for Lighting
Indicator for lighting
ON / OFF
-
Indicator Condition
Power switch indicator
Green / Amber / No Sig
-
P Supply for Steering Lock
Power supply for steering lock ECU
ON / OFF
-