Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

TIRE PRESSURE WARNING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the Techstream to read the DATA LIST allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the DATA LIST information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Turn the power switch off.

  2. Connect the Techstream to the DLC3.

  3. Turn the power switch on (IG) and turn the Techstream on.

  4. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  5. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Mode Status
    Tire pressure warning system mode/NORMAL or TEST
    NORMAL: Normal mode
    TEST: Test mode
    -
    Main Tire
    Number of main tire ID that are registered/4 or 5
    4 or 5 is displayed
    -
    2nd Tire*3
    Number of 2nd tire ID that are registered/4 or 5
    -
    -
    Select Switch*3
    Select switch/Main or 2nd
    -
    -
    Initialization Switch*3
    Tire pressure warning reset switch/ON or OFF
    -
    -
    Vehicle Speed
    Vehicle speed reading/min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)
    Actual vehicle speed
    Speed indicated on the combination meter
    Registered ID1 Code
    Registered ID1 code/min.: 0, max.: FFFFFFF*1
    The ID No. registered in the transmitter ID1 is displayed
    -
    Registered ID2 Code
    Registered ID2 code/min.: 0, max.: FFFFFFF*1
    The ID No. registered in the transmitter ID2 is displayed
    -
    Registered ID3 Code
    Registered ID3 code/min.: 0, max.: FFFFFFF*1
    The ID No. registered in the transmitter ID3 is displayed
    -
    Registered ID4 Code
    Registered ID4 code/min.: 0, max.: FFFFFFF*1
    The ID No. registered in the transmitter ID4 is displayed
    -
    Registered ID5 Code
    Registered ID5 code/min.: 0, max.: FFFFFFF*1
    The ID No. registered in the transmitter ID5 is displayed
    -
    ID1 Tire Inflation Pressure
    ID1 tire inflation pressure/
    min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure/ 637.5 kPa (6.5 kgf/cm2, 92.5 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*2
    ID2 Tire Inflation Pressure
    ID2 tire inflation pressure/
    min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure / 637.5 kPa (6.5 kgf/cm2, 92.5 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*2
    ID3 Tire Inflation Pressure
    ID3 tire inflation pressure/
    min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure / 637.5 kPa (6.5 kgf/cm2, 92.5 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*2
    ID4 Tire Inflation Pressure
    ID4 tire inflation pressure/
    min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure / 637.5 kPa (6.5 kgf/cm2, 92.5 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*2
    ID5 Tire Inflation Pressure
    ID5 tire inflation pressure/
    min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure / 637.5 kPa (6.5 kgf/cm2, 92.5 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*2
    ID1 Temperature in Tire
    ID1 temperature in tire/min.: -40°C (-40°F), max.: 215°C (419°F)
    Actual tire temperature
    If -40°C (-40°F) is displayed, data has not been received.
    ID2 Temperature in Tire
    ID2 temperature in tire/min.: -40°C (-40°F), max.: 215°C (419°F)
    Actual tire temperature
    If -40°C (-40°F) is displayed, data has not been received.
    ID3 Temperature in Tire
    ID3 temperature in tire/min.: -40°C (-40°F), max.: 215°C (419°F)
    Actual tire temperature
    If -40°C (-40°F) is displayed, data has not been received.
    ID4 Temperature in Tire
    ID4 temperature in tire/min.: -40°C (-40°F), max.: 215°C (419°F)
    Actual tire temperature
    If -40°C (-40°F) is displayed, data has not been received.
    ID5 Temperature in Tire
    ID5 temperature in tire/min.: -40°C (-40°F), max.: 215°C (419°F)
    Actual tire temperature
    If -40°C (-40°F) is displayed, data has not been received.
    ID1 Battery Voltage
    ID1 battery voltage/Over or Less
    Over
    -
    ID2 Battery Voltage
    ID2 battery voltage/Over or Less
    Over
    -
    ID3 Battery Voltage
    ID3 battery voltage/Over or Less
    Over
    -
    ID4 Battery Voltage
    ID4 battery voltage/Over or Less
    Over
    -
    ID5 Battery Voltage
    ID5 battery voltage/Over or Less
    Over
    -
    ID1 Initial Threshold of Low-pressure
    ID1 initial threshold of low-pressure/min.: -100 kPa (-1 kgf/cm2, -14 psi), max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Tire pressure after initialization
    -
    ID2 Initial Threshold of Low-pressure
    ID2 initial threshold of low-pressure/min.: -100 kPa (-1 kgf/cm2, -14 psi), max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Tire pressure after initialization
    -
    ID3 Initial Threshold of Low-pressure
    ID3 initial threshold of low-pressure/min.: -100 kPa (-1 kgf/cm2, -14 psi), max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Tire pressure after initialization
    -
    ID4 Initial Threshold of Low-pressure
    ID4 initial threshold of low-pressure/min.: -100 kPa (-1 kgf/cm2, -14 psi), max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Tire pressure after initialization
    -
    ID5 Initial Threshold of Low-pressure
    ID5 initial threshold of low-pressure/min.: -100 kPa (-1 kgf/cm2, -14 psi), max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Tire pressure after initialization
    -
    Select Switch Info
    Select switch setting information/With or Without
    Without
    -
    Initialization SW Info
    Tire pressure warning reset switch setting information/With or Without
    Without
    -
    Number of DTC
    Number of DTCs recorded/min.: 0, max.: 255
    0
    -

    HINT:
    *1: Displayed only when the ID No. is not registered.
    *2: It may take about 2 to 3 minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2125/25 (Click here).
    *3: This item will be displayed on the Techstream, but it does not apply this model.


ACTIVE TEST

HINT:
Using the Techstream to perform ACTIVE TEST allows the meters, indicators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing ACTIVE TEST early in troubleshooting is one way to save diagnostic time. It is possible to display the DATA LIST on the Techstream during ACTIVE TEST.

  1. Turn the power switch off.

  2. Connect the Techstream to the DLC3.

  3. Turn the power switch on (IG) and turn the Techstream on.

  4. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  5. According to the display on the Techstream, perform the "ACTIVE TEST".

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. Tire Pressure Warning System
    Tire Pressure Warning Light
    Tire pressure warning light is OFF/ON
    Confirm that the vehicle is stopped, engine idling