Home › BODY ELECTRICAL › DOOR LOCK › SMART KEY SYSTEM

SMART KEY SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


  1. Disconnect the D40 certification ECU (smart key ECU assembly) connector.


    B178888E01

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D40-1 (+B) - Body ground
    B - Body ground
    +B power supply
    Always
    11 to 14 V
    D40-3 (TSW1) - Body ground
    LG - Body ground
    Entry lock switch (driver side) signal
    Front lock switch not pushed
    10 kΩ or higher
    D40-3 (TSW1) - Body ground
    LG - Body ground
    Entry lock switch (driver side) signal
    Front lock switch pushed
    Below 1 Ω
    D40-4 (TSW2) - Body ground
    GR - Body ground
    Entry lock switch (front passenger side) signal
    Front lock switch not pushed
    10 kΩ or higher
    D40-4 (TSW2) - Body ground
    GR - Body ground
    Entry lock switch (front passenger side) signal
    Front lock switch pushed
    Below 1 Ω
    D40-7 (TSW5) - Body ground
    BR - Body ground
    Back door entry lock switch signal
    Lock switch OFF
    10 kΩ or higher
    D40-7 (TSW5) - Body ground
    BR - Body ground
    Back door entry lock switch signal
    Lock switch ON
    Below 1 Ω
    D40-10 (LIN) - Body ground
    L - Body ground
    LIN line
    Always
    10 kΩ or higher
    D40-17 (E) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    D40-18 (IG) - Body ground
    G - Body ground
    Ignition power supply
    Power switch off
    Below 1 V
    D40-18 (IG) - Body ground
    G - Body ground
    Ignition power supply
    Power switch on (IG)
    11 to 14 V
    D40-19 (ACC) - Body ground
    SB - Body ground
    ACC power supply
    Power switch off
    Below 1 V
    D40-19 (ACC) - Body ground
    SB - Body ground
    ACC power supply
    Power switch on (ACC)
    11 to 14 V
    D40-27 (CANH) - Body ground
    B - Body ground
    CAN line
    Always
    10 kΩ or higher
    D40-28 (CANL) - Body ground
    W - Body ground
    CAN line
    Always
    10 kΩ or higher
    D40-40 (AGND) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, the wire harness may have a malfunction.

  3. Reconnect the D40 certification ECU (smart key ECU assembly) connector.

  4. Measure the voltage and resistance according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D40-5 (SEL1) - D40-17 (E)
    P - B
    Touch sensor (driver side) activation control signal
    The key is moved more than 5 m (16.4 ft.) away from the front door.
    11 to 14 V
    D40-5 (SEL1) - D40-17 (E)
    P - B
    Touch sensor (driver side) activation control signal
    The key is moved to the door outside handle.
    Below 1 V
    D40-6 (SEL2) - D40-17 (E)
    Y - B
    Touch sensor (front passenger side) activation control signal
    The key is moved more than 5 m (16.4 ft.) away from the front passenger door.
    11 to 14 V
    D40-6 (SEL2) - D40-17 (E)
    Y - B
    Touch sensor (front passenger side) activation control signal
    The key is moved to the door outside handle.
    Below 1 V
    D40-8 (TXCT) - Body ground
    O - Body ground
    Transponder key amplifier output signal
    Electrical key is not in the cabin.
    Below 1 V
    D40-8 (TXCT) - Body ground
    O - Body ground
    Transponder key amplifier output signal
    Electrical key is outside the cabin and the driver's door is open.
    Pulse generation (see waveform 1)
    D40-9 (CODE) - Body ground
    GR - Body ground
    Transponder key amplifier communication signal
    Electrical key is not in the cabin.
    Below 1 V
    D40-9 (CODE) - Body ground
    GR - Body ground
    Transponder key amplifier communication signal
    Electrical key is outside the cabin and the driver's door is open. Electrical key is held close to the Power switch with the brake pedal depressed.
    Pulse generation (see waveform 2)
    D40-11 (CLG5) - D40-12 (CG5B)
    R - W
    Indoor electrical key oscillator (front) sensor signal
    Within 30 seconds after driver side door opened and closed, power switch off
    Alternating between 5 V and below -5 V
    D40-11 (CLG5) - D40-12 (CG5B)
    R - W
    Indoor electrical key oscillator (front) sensor signal
    Power switch on (IG)
    Below 1 V
    D40-13 (CLG6) - D40-14 (CG6B)
    R - SB
    Indoor electrical key oscillator (center) sensor signal
    Within 30 seconds after driver side door opened and closed, power switch off
    Alternating between 5 V and below -5 V
    D40-13 (CLG6) - D40-14 (CG6B)
    R - SB
    Indoor electrical key oscillator (center) sensor signal
    Power switch on (IG)
    Below 1 V
    D40-15 (CLG7) - D40-16 (CG7B)
    G - O
    Indoor electrical key oscillator (rear) sensor signal
    Within 30 seconds after driver side door opened and closed, power switch off
    Alternating between 5 V and below -5 V
    D40-15 (CLG7) - D40-16 (CG7B)
    G - O
    Indoor electrical key oscillator (rear) sensor signal
    Power switch on (IG)
    Below 1 V
    D40-21 (BZR) - Body ground
    R - Body ground
    Wireless door lock buzzer signal
    Wireless door lock buzzer OFF
    Below 1 V
    D40-21 (BZR) - Body ground
    R - Body ground
    Wireless door lock buzzer signal
    Wireless door lock buzzer ON
    Pulse generation
    D40-22 (SEN1) - D40-17 (E)
    O - B
    Touch sensor (driver side) detection signal
    Door outside handle touched
    Below 1 V
    D40-22 (SEN1) - D40-17 (E)
    O - B
    Touch sensor (driver side) detection signal
    Door outside handle not touched (the electrical key is outside the cabin)
    11 to 14 V
    D40-23 (SEN2) - D40-17 (E)
    W - B
    Touch sensor (front passenger side) detection signal
    Door outside handle touched
    Below 1 V
    D40-23 (SEN2) - D40-17 (E)
    W - B
    Touch sensor (front passenger side) detection signal
    Door outside handle not touched (the electrical key is outside the cabin)
    11 to 14 V
    D40-29 (RC0) - D40-17 (E)
    V - B
    Entry door control receiver power source
    Power switch off, all doors closed and electrical key switch on
    4.5 to 5.5 V
    D40-29 (RC0) - D40-17 (E)
    V - B
    Entry door control receiver power source
    Power switch off, all doors closed and electrical key switch off
    Below 1 V
    D40-30 (VC5) - Body ground
    G - Body ground
    Transponder key amplifier power supply
    Electrical key is not in the cabin.
    Below 1 V
    D40-30 (VC5) - Body ground
    G - Body ground
    Transponder key amplifier power supply
    Electrical key is outside the cabin and the driver's door is open.
    4.5 to 5.5 V
    D40-31 (CLG8) - D40-32 (CG8B)
    LG - P
    Outside electrical key oscillator (back door) sensor signal
    Back door opener switch ON
    Alternating between 5 V and below -5 V
    D40-31 (CLG8) - D40-32 (CG8B)
    LG - P
    Outside electrical key oscillator (back door) sensor signal
    Back door opener switch OFF
    Below 1 V
    D40-33 (CLG1) - D40-17 (E)
    GR - B
    Door electrical key oscillator (driver side) sensor signal
    All doors closed and locked and power switch off
    Alternating between 5 V and below 1 V
    D40-33 (CLG1) - D40-17 (E)
    GR - B
    Door electrical key oscillator (driver side) sensor signal
    Door unlocked or open
    Below 1 V
    D40-35 (CLG2) - D40-17 (E)
    LG - B
    Door electrical key oscillator (front passenger side) sensor signal
    All doors closed and locked and power switch off
    Alternating between 5 V and below 1 V
    D40-35 (CLG2) - D40-17 (E)
    LG - B
    Door electrical key oscillator (front passenger side) sensor signal
    Door unlocked or open
    Below 1 V
    D40-38 (RDA) - D40-17 (E)
    Y - B
    Entry door control receiver data input signal
    Power switch off, all doors closed and electrical key switch off
    11 to 14 V
    (Pulse generation)
    D40-38 (RDA) - D40-17 (E)
    Y - B
    Entry door control receiver data input signal
    Power switch off, all doors closed and electrical key switch on
    Pulse generation
    D40-38 (RDA) - Body ground
    Y - Body ground
    Tuner input signal
    Power switch off, all doors closed, and the electrical key is not in the detection area.
    11 to 14 V
    (Pulse generation)
    D40-38 (RDA) - Body ground
    Y - Body ground
    Tuner input signal
    The electrical key is in the detection area.
    Pulse generation
    D40-39 (RSSI) - D40-17 (E)
    B - B
    Entry door control receiver electric wave existence signal
    Power switch off, all doors closed, and the electrical key is not in the detection area.
    11 to 14 V
    D40-39 (RSSI) - D40-17 (E)
    B - B
    Entry door control receiver electric wave existence signal
    Power switch off, all doors closed, and the electrical key is in the detection area.
    Below 1 V
    If the result is not as specified, the ECU may have a malfunction.



  5. B164407E01
  6. Inspect using an oscilloscope.
    Waveform 1 (Reference): 
    Tester Connection
    D40-8 (TXCT) - Body ground
    Tool Setting
    2 V/DIV., 50 ms./DIV.
    Condition
    The electrical key is outside the cabin and the driver's door is open.



  7. B164408E01
  8. Inspect using an oscilloscope.
    Waveform 2 (Reference): 
    Tester Connection
    D40-9 (CODE) - Body ground
    Tool Setting
    2 V/DIV., 50 ms./DIV.
    Condition
    The electrical key is outside the cabin and the driver's door is open. The electrical key is held close to the power switch with the brake pedal depressed.


MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
  1. Disconnect the 1M and 1F junction block connectors.



  2. Disconnect the D9 main body ECU (instrument panel junction block) connector.


    B112605E16

  3. Measure the resistance according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    1M-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1F-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    D9-15 (CANN) - Body ground
    W - Body ground
    CAN line
    Always
    10 kΩ or higher
    D9-16 (CANP) - Body ground
    B - Body ground
    CAN line
    Always
    10 kΩ or higher
    If the result is not as specified, the wire harness may have a malfunction.

  4. Reconnect the 1M and 1F junction block connectors.

  5. Reconnect the D9 main body ECU (instrument panel junction block ) connector.

  6. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    1M-7 (STP) - Body ground
    GR - Body ground
    Stop light switch signal
    Brake pedal depressed
    11 to 14 V
    1M-7 (STP) - Body ground
    GR - Body ground
    Stop light switch signal
    Brake pedal released
    Below 1 V
    If the result is not as specified, the ECU may have a malfunction.