Home › BODY ELECTRICAL › DOOR LOCK › SMART KEY SYSTEM

SMART KEY SYSTEM > Driver Side Door Entry Lock Function does not Operate

for Preparation Click here


DESCRIPTION

If the driver door entry lock function does not operate but the entry unlock function operates, the communication line between the vehicle and electrical key transmitter is normal. As a faulty part, the entry lock switch circuit (certification ECU (smart key ECU assembly) → driver side door outside handle (entry lock switch) → driver side door electrical key oscillator) can be considered.

WIRING DIAGRAM


B164327E11


INSPECTION PROCEDURE

NOTICE:
Before performing the inspection, check that there are no problems related to "CAN COMMUNICATION SYSTEM" and "LIN COMMUNICATION SYSTEM".

1.CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the master switch assembly is operated, check that the locked doors unlock (Click here).

    OK:
    Locked doors unlock.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2.READ VALUE ON TECHSTREAM (DOOR OUTSIDE HANDLE)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus:
    Body Electrical / Smart Key / Data List.

  1. Select D-Door Trigger Switch in the Data List and read the Techstream display.

    Smart Key (Certification ECU (Smart Key ECU Assembly)): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D-Door Trigger Switch
    Driver side door lock switch / ON or OFF
    ON: Entry lock switch is pressed
    OFF: Entry lock switch is not pressed
    -

    OK:
    On the tester screen, the item changes between ON and OFF according to the chart above.



NG
Go to step 3
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (Click here)  

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR)


    B164339E27
  1. Remove the front door outside handle (Click here).

  1. Disconnect the door electrical key oscillator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    z13-1 (TRG-) - z14-9 (TRG-)
    Always
    Below 1 Ω
    z13-1 (TRG-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)


    B171408E01
  1. Disconnect the certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D40-3 (TSW1) - z13-3 (TRG+)
    Always
    Below 1 Ω
    D40-3 (TSW1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT FRONT DOOR OUTSIDE HANDLE (DRIVER SIDE)


    B112465E30
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    z13-1 (TRG-) - z13-3 (TRG+)
    Lock switch not pushed
    10 kΩ or higher
    z13-1 (TRG-) - z13-3 (TRG+)
    Lock switch pushed
    Below 1 Ω



NG
REPLACE FRONT DOOR OUTSIDE HANDLE (Click here)
OK


6.REPLACE DOOR ELECTRICAL KEY OSCILLATOR
  1. Replace the door electrical key oscillator (Click here).


NEXT


7.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
  1. Check that the entry functions operate normally.

    OK:
    Entry functions operate normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (Click here)
OK

END (DOOR ELECTRICAL OSCILLATOR IS DEFECTIVE)