Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here


NOTICE:
  1. Turn the power switch off before measuring the resistances of the CAN bus main wires and CAN bus branch wires.
  2. After the power switch is turned off, check that the key reminder warning system and light remainder warning system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the power switch, any other switches, or the doors. If any doors need to be opened in order to check the connectors, open the doors and leave them open.

HINT:
Operating the power switch, any other switches, or a door triggers related ECU and sensor communication on the CAN.
This communication will cause the resistance value to change.

NOTICE:
This section describes the standard CAN values for all CAN related components.


JUNCTION CONNECTOR FOR CAN BUS


  1. CAN junction connector CTR


    C132298E25


    CAN Junction Connector CTR
    Wiring Color
    Connect to
    D55-1 (CANH)
    B
    CAN junction connector RH
    D55-12 (CANL)
    W
    CAN junction connector RH
    D55-2 (CANH)
    B
    Yaw rate sensor
    D55-13 (CANL)
    W
    Yaw rate sensor
    D55-3 (CANH)
    B
    Center airbag sensor assembly
    D55-14 (CANL)
    W
    Center airbag sensor assembly
    D55-4 (CANH)
    B
    DLC3
    D55-15 (CANL)
    W
    DLC3
    D55-5 (CANH)
    B
    Steering angle sensor
    D55-16 (CANL)
    W
    Steering angle sensor
    D55-6 (CANH)
    B
    Combination meter
    D55-17 (CANL)
    W
    Combination meter
    D55-7 (CANH)
    B
    Power steering ECU
    D55-18 (CANL)
    W
    Power steering ECU
    D55-8 (CANH)
    B
    Main body ECU
    D55-19 (CANL)
    W
    Main body ECU



  2. CAN junction connector RH


    C132298E24


    CAN Junction Connector RH
    Wiring Color
    Connect to
    D59-1 (CANH)
    B
    Hybrid vehicle control ECU
    D59-12 (CANL)
    W
    Hybrid vehicle control ECU
    D59-2 (CANH)
    B
    Accessory gateway
    D59-13 (CANL)
    W
    Accessory gateway
    D59-3 (CANH)
    B
    Air conditioning amplifier
    D59-14 (CANL)
    W
    Air conditioning amplifier
    D59-4 (CANH)
    B
    Skid control ECU
    D59-15 (CANL)
    W
    Skid control ECU
    D59-5 (CANH)
    B
    CAN junction connector CTR
    D59-16 (CANL)
    W
    CAN junction connector CTR
    D59-6 (CANH)
    B
    Navigation receiver assembly
    D59-17 (CANL)
    W
    Navigation receiver assembly



  3. The connection diagram of the components which are connected to the CAN junction connector.


    C175437E01


JUNCTION CONNECTOR FOR CAN MS BUS (w/ POWER BACK DOOR SYSTEM)


  1. CAN junction connector LH


    C178028E01


    CAN Junction Connector RH
    Wiring Color
    Connect to
    D54-11 (CANH)
    B
    1. Certification ECU (w/o Power back door system)
    2. CAN junction connector RR (w/ Power back door system)
    D54-2 (CANL)
    W
    1. Certification ECU (w/o Power back door system)
    2. CAN junction connector RR (w/ Power back door system)
    D54-10 (CANH)
    B
    Main body ECU
    D54-3 (CANL)
    W
    Main body ECU
    D54-9 (CANH)
    B
    Tire pressure warning ECU
    D54-8 (CANL)
    W
    Tire pressure warning ECU



  2. CAN junction connector RR (w/ Power back door system)


    C167481E06


    CAN Junction Connector RR
    Connector color
    Wiring Color
    Connect to
    O21-1 (CANH)
    B
    B
    Back door ECU
    O21-2 (CANL)
    W
    Back door ECU
    O23-1 (CANH)
    N
    B
    Certification ECU
    O23-2 (CANL)
    W
    Certification ECU
    O24-1 (CANH)
    GR
    B
    CAN junction Connector LH
    O24-2 (CANL)
    W
    CAN junction Connector LH



  3. The connection diagram of the components which are connected to the CAN junction connector.


    C175440E01


DLC3


    C125062E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D47-6 (CANH) - D47-14 (CANL)
    B - W
    Power switch off
    54 to 69 Ω
    D47-6 (CANH) - D47-4 (CG)
    B - B
    Power switch off
    200 Ω or higher
    D47-14 (CANL) - D47-4 (CG)
    W - B
    Power switch off
    200 Ω or higher
    D47-6 (CANH) - D47-16 (BAT)
    B - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D47-14 (CANL) - D47-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


SKID CONTROL ECU

C138589E06



    C113751E07
  1. Disconnect the connector from the skid control ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    A44-19 (CANH) - A44-18 (CANL)
    B - W
    Power switch off
    54 to 69 Ω
    A44-19 (CANH) - A46-1 (GND)
    B - W-B
    Power switch off
    200 Ω or higher
    A44-18 (CANL) - A46-1 (GND)
    W - W-B
    Power switch off
    200 Ω or higher
    A44-19 (CANH) - A44-3 (+BI1)
    B - B
    Negative battery terminal disconnected
    6 kΩ or higher
    A44-18 (CANL) - A44-3 (+BI1)
    W - B
    Negative battery terminal disconnected
    6 kΩ or higher


STEERING ANGLE SENSOR


    C146385E02
  1. Disconnect the connector from the steering angle sensor.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D14-3 (CANH) - D14-2 (CANL)
    B - W
    Power switch off
    54 to 69 Ω
    D14-3 (CANH) - D14-1 (ESS)
    B - GR
    Power switch off
    200 Ω or higher
    D14-2 (CANL) - D14-1 (ESS)
    W - GR
    Power switch off
    200 Ω or higher
    D14-3 (CANH) - D14-5 (BAT)
    B - BR
    Negative battery terminal disconnected
    6 kΩ or higher
    D14-2 (CANL) - D14-5 (BAT)
    W - BR
    Negative battery terminal disconnected
    6 kΩ or higher


YAW RATE SENSOR


    C152858E03
  1. Disconnect the connector from the yaw rate sensor.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    O6-3 (CANH) - O6-2 (CANL)
    B - W
    Power switch off
    54 to 69 Ω
    O6-3 (CANH) - O6-1 (GND)
    B - W-B
    Power switch off
    200 Ω or higher
    O6-2 (CANL) - O6-1 (GND)
    W - W-B
    Power switch off
    200 Ω or higher
    O6-3 (CANH) - D47-16 (BAT)
    B - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    O6-2 (CANL) - D47-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


CENTER AIRBAG SENSOR ASSEMBLY


    C152878E08
  1. Disconnect the connector from the center airbag sensor assembly.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D30-13 (CANH) - D30-22 (CANL)
    B - W
    Power switch off
    54 to 69 Ω
    D30-13 (CANH) - D30-25 (E1)
    B - B
    Power switch off
    200 Ω or higher
    D30-22 (CANL) - D30-25 (E1)
    W - B
    Power switch off
    200 Ω or higher
    D30-13 (CANH) - D47-16 (BAT)
    B - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D30-22 (CANL) - D47-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


HYBRID VEHICLE CONTROL ECU

C175441E01

  1. Disconnect the connector from the hybrid vehicle control ECU.



  2. C113752E07
  3. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D36-25 (CANH) - D36-33 (CANL)
    B - W
    Power switch off
    108 to 132 Ω
    D36-25 (CANH) - D36-32 (EOM)
    B - W-B
    Power switch off
    200 Ω or higher
    D36-33 (CANL) - D36-32 (EOM)
    W - W-B
    Power switch off
    200 Ω or higher
    D36-25 (CANH) - D35-1 (BATT)
    B - R
    Negative battery terminal disconnected
    6 kΩ or higher
    D36-33 (CANL) - D35-1 (BATT)
    W - R
    Negative battery terminal disconnected
    6 kΩ or higher


AIR CONDITIONING AMPLIFIER
C152868E02
  1. Disconnect the amplifier connector from the air conditioning amplifier.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D37-11 (CANH) - D37-12 (CANL)
    B - W
    Power switch off
    54 to 69 Ω
    D37-11 (CANH) - D37-14 (GND)
    B - W-B
    Power switch off
    200 Ω or higher
    D37-12 (CANL) - D37-14 (GND)
    W - W-B
    Power switch off
    200 Ω or higher
    D37-11 (CANH) - D37-21 (B)
    B - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D37-12 (CANL) - D37-21 (B)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


COMBINATION METER


    C109571E20
  1. Disconnect the connector from the combination meter.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    E1-25 (CANH) - E1-26 (CANL)
    B - W
    Power switch off
    108 to 132 Ω
    E1-25 (CANH) - E1-20 (ES)
    B - R
    Power switch off
    200 Ω or higher
    E1-26 (CANL) - E1-20 (ES)
    W - R
    Power switch off
    200 Ω or higher
    E1-25 (CANH) - E1-21 (B)
    B - SB
    Negative battery terminal disconnected
    6 kΩ or higher
    E1-26 (CANL) - E1-21 (B)
    W - SB
    Negative battery terminal disconnected
    6 kΩ or higher


CERTIFICATION ECU


    C152870E04
  1. Disconnect the connector from the certification ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D40-27 (CANH) - D40-28 (CANL)
    B - W
    Power switch off
    54 to 69 Ω
    D40-27 (CANH) - D40-17 (E)
    B - B
    Power switch off
    200 Ω or higher
    D40-28 (CANL) - D40-17 (E)
    W - B
    Power switch off
    200 Ω or higher
    D40-27 (CANH) - D40-1 (+B)
    B - B
    Negative battery terminal disconnected
    6 kΩ or higher
    D40-28 (CANL) - D40-1 (+B)
    W - B
    Negative battery terminal disconnected
    6 kΩ or higher


MAIN BODY ECU
  1. Disconnect the connector from the main body ECU.



  2. C178535E01
  3. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D9-5 (CANH) - D9-6 (CANL)
    B - W
    Power switch off
    54 to 69 Ω
    D9-5 (CANH) - D47-4 (CG)
    B - B
    Power switch off
    200 Ω or higher
    D9-6 (CANL) - D47-4 (CG)
    W - B
    Power switch off
    200 Ω or higher
    D9-5 (CANH) - D47-16 (BAT)
    B - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D9-6 (CANL) - D47-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D9-16 (CANP) - D9-15 (CANN)
    B - W
    Power switch off
    108 to 132 Ω
    D9-16 (CANP) - D47-4 (CG)
    B - B
    Power switch off
    200 Ω or higher
    D9-15 (CANN) - D47-4 (CG)
    W - B
    Power switch off
    200 Ω or higher
    D9-16 (CANP) - D47-16 (BAT)
    B - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D9-15 (CANN) - D47-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


POWER STEERING ECU


    C160514E10
  1. Disconnect the power steering ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D6-2 (CANH) - D6-8 (CANL)
    B - W
    Power switch off
    54 to 69 Ω
    D6-2 (CANH) - D5-2 (PGND)
    B - W
    Power switch off
    200 Ω or higher
    D6-8 (CANL) - D5-2 (PGND)
    W - W
    Power switch off
    200 Ω or higher
    D6-2 (CANH) - D5-1 (PIG)
    B - B
    Negative battery terminal disconnected
    6 kΩ or higher
    D6-8 (CANL) - D5-1 (PIG)
    W - B
    Negative battery terminal disconnected
    6 kΩ or higher


NAVIGATION RECEIVER ASSEMBLY (w/ NAVIGATION SYSTEM)


    C170022E03
  1. Disconnect the navigation receiver assembly connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    E4-2 (CANH) - E4-3 (CANL)
    B - W
    Power switch off
    54 to 69 Ω
    E4-2 (CANH) - D47-4 (CG)
    B - B
    Power switch off
    200 Ω or higher
    E4-3 (CANL) - D47-4 (CG)
    W - B
    Power switch off
    200 Ω or higher
    E4-2 (CANH) - D47-16 (BAT)
    B - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    E4-3 (CANL) - D47-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


TIRE PRESSURE WARNING ECU


    C178538E01
  1. Disconnect the tire pressure warning ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D33-6 (CANP) - D33-12 (CANN)
    B - W
    Power switch off
    54 to 69 Ω
    D33-6 (CANP) - D33-7 (GND)
    B - W-B
    Power switch off
    200 Ω or higher
    D33-12 (CANN) - D33-7 (GND)
    W - W-B
    Power switch off
    200 Ω or higher
    D33-6 (CANP) - D47-16 (BAT)
    B - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D33-12 (CANN) - D47-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


BACK DOOR ECU (w/ POWER BACK DOOR SYSTEM)


    C169769E01
  1. Disconnect the back door ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    O15-6 (MPX1) - O15-5 (MPX2)
    B - W
    Power switch off
    54 to 69 Ω
    O15-6 (MPX1) - O15-11 (GND)
    B - W-B
    Power switch off
    200 Ω or higher
    O15-5 (MPX2) - O15-11 (GND)
    W - W-B
    Power switch off
    200 Ω or higher
    O15-6 (MPX1) - O15-12 (B)
    B - B
    Negative battery terminal disconnected
    6 kΩ or higher
    O15-5 (MPX2) - O15-12 (B)
    W - B
    Negative battery terminal disconnected
    6 kΩ or higher


ACCESSORY GATEWAY


    C169659E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    D50-1 (CAN+) - D50-2 (CAN-)
    B - W
    Power switch off
    54 to 69 Ω
    D50-1 (CAN+) - D47-4 (CG)
    B - B
    Power switch off
    200 Ω or higher
    D50-2 (CAN-) - D47-4 (CG)
    W - B
    Power switch off
    200 Ω or higher
    D50-1 (CAN+) - D47-16 (BAT)
    B - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D50-2 (CAN-) - D47-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher