HOOD LOCK CONTROL CABLE ASSEMBLY > INSTALLATION |
| 1. INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY |
Pass the hood lock control cable assembly into the engine compartment.

| Area | Part Name | Area | Part Name |
| A | Hood lock control cable | E | Fender liner |
| B | Clamp | F | Hood stopper rubber |
| C | Hood cable grommet | G | Front washer hose |
| D | Wire harness | H | Rear washer hose |
Pass the cable through the upper radiator support.
Connect the clamps as shown in the illustration.
![]() |
Connect the hood lock control cable to the hood lock control lever.
| 2. INSTALL HOOD LOCK ASSEMBLY (w/o Engine Hood Courtesy Switch) |
![]() |
Apply MP grease to the sliding areas of the lock.
![]() |
Connect the hood lock control cable.
![]() |
Install the hood lock assembly with the 3 bolts.
![]() |
Install the hood lock nut cap.
| 3. INSTALL HOOD LOCK ASSEMBLY (w/ Engine Hood Courtesy Switch) |
![]() |
Apply MP grease to the sliding areas of the lock.
![]() |
Connect the hood lock control cable.
![]() |
Install the hood lock assembly with the 3 bolts.
![]() |
Install the hood lock nut cap.
![]() |
Connect the connector.
| 4. INSPECT HOOD SUB-ASSEMBLY |
Check that the clearance measurements of areas A through D are within each standard range.

| Area | Measurement | Area | Measurement |
| A | 6.2 to 10.2 mm (0.244 to 0.402 in.) | C | 2.5 to 5.5 mm (0.098 to 0.217 in.) |
| B | 5.9 to 9.9 mm (0.232 to 0.390 in.) | D | -1.5 to 1.5 mm (-0.059 to 0.059 in.) |
| 5. ADJUST HOOD SUB-ASSEMBLY |
Horizontally and vertically adjust the hood.
![]() |
Loosen the 4 hinge bolts of the hood.
Adjust the clearance between the hood and front fender by moving the hood.
Tighten the 4 hinge bolts after the adjustment.
Adjust the height of the front end of the hood using the cushion rubber.
![]() |
Adjust the cushion rubbers so that the heights of the hood and fender are aligned.
Adjust the hood lock.
![]() |
Remove the hood lock nut cap.
![]() |
Loosen the 3 bolts.
Tighten the bolts after the adjustment.
![]() |
Install the hood lock nut cap.
Check that the striker can engage with the hood lock smoothly.
| 6. INSTALL RADIATOR GRILLE |
![]() |
Engage the 4 guides and 6 claws, and install the radiator grille.
![]() |
Install the 4 clips and 2 bolts.
| 7. INSTALL COOL AIR INTAKE DUCT SEAL |
![]() |
Install the cool air intake duct seal with the 11 clips.
| 8. INSTALL FRONT FENDER LINER LH |
![]() |
Install the front fender liner LH with the 5 clips and 8 screws.
![]() |
Install 2 new grommets.
Using a 4 mm hexagon wrench, install the 2 screws.
![]() |
Install the screw and pin hold clip.
| 9. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY LH |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove the front fender side protector from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
![]() |
Clean the front fender moulding sub-assembly. (If reusing the front fender moulding sub-assembly)
Using a heat light, heat the front fender moulding sub-assembly.
Remove the front fender side protector from the front fender moulding sub-assembly.
Wipe off any tape adhesive residue with cleaner.
Install a new front fender side protector to the the front fender moulding sub-assembly.
Install 2 new No. 4 clips on the front fender moulding sub-assembly.
Install a new pad on the front fender moulding sub-assembly.
![]() |
Install the front fender moulding sub-assembly.
Using a heat light, heat the vehicle body and the front fender moulding sub-assembly.
Remove the release paper from the front fender moulding sub-assembly.
Engage the 3 clips and install the front fender moulding sub-assembly.
![]() |
Using a 4 mm hexagon wrench, install the screw.
Install the clip.
| 10. INSTALL NO. 1 ENGINE UNDER COVER |
Install the 6 bolts, 2 screws, 2 clips and No. 1 engine under cover.