Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B1471/71    A/C Inverter High Voltage Power Resource System Malfunction

for Preparation Click here


DESCRIPTION

The A/C inverter assembly monitors power voltage from the main battery in the circuit. It stops compressor control and outputs the DTC when the monitored voltage is outside the specified range.
The output DTC is memorized as previous trouble. Compressor control can not resume until the power switch is turned off.

CAUTION:
  1. Wear electrically insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Be sure to carry the removed service plug grip to prevent other technicians from accidentally reinstalling it.
  2. Do not touch the high-voltage connectors or terminals for 5 minutes after the service plug grip is removed.
  3. When working on high voltage wiring or components, be sure to follow all safety precautions listed in the HYBRID VEHICLE CONTROL section (Click here).

NOTICE:
The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs for the hybrid control system first if any DTCs from that system are output simultaneously.


DTC No.
DTC Detection Condition
Trouble Area
B1471/71
  1. Open or short in A/C inverter high voltage power resource system circuit
  2. The boost pressure system is broken or malfunctioning.
  1. Harness or connector between compressor with motor assembly and inverter with converter assembly
  2. Compressor with motor assembly
  3. Hybrid control system
  4. Inverter with converter assembly
  5. CAN communication system

WIRING DIAGRAM


E158954E03


INSPECTION PROCEDURE

CAUTION:
  1. Wear electrically insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Be sure to carry the removed service plug grip to prevent other technicians from accidentally reinstalling it.
  2. Do not touch the high-voltage connectors or terminals for 5 minutes after the service plug grip is removed.
  3. Verify that the voltage of the inverter with converter assembly is 0V before working inside the inverter with converter assembly.
  4. After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY) unless instructed by the repair manual.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Using the Techstream, check if the CAN communication system is functioning normally.

    Result:
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK FOR DTC (HYBRID CONTROL SYSTEM)
  1. Check if DTCs for the hybrid control system are output using the Techstream.

    OK:
    Hybrid control system DTCs are not output.



NG
GO TO HYBRID CONTROL SYSTEM (Click here)
OK


3.INSPECT ELECTRIC VEHICLE FUSE
  1. Turn the power switch off.

  1. Remove the service plug grip.

    CAUTION:
    1. Be sure to wear insulated gloves.
    2. Do not touch the high-voltage connectors or terminals for 5 minutes after the service plug grip is removed.

    NOTICE:
    After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY) unless instructed by the repair manual.



    A108528E01
  1. Remove the inverter cover assembly.

    CAUTION:
    1. Be sure to wear insulated gloves.
    2. Verify that the voltage of the inverter with converter assembly is 0V before working inside the inverter with converter assembly.

    NOTICE:
    Be sure to prevent foreign objects or liquid from entering the inverter with converter assembly.



    E110725E01
  1. Check that bolts A and B are tightened securely.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Tester Item
    (Tester Connection)
    Condition
    Specified Condition
    ELECTRIC VEHICLE fuse
    (A - B)
    Always
    Below 1 Ω



NG
REPLACE ELECTRIC VEHICLE FUSE
OK


4.INSPECT INVERTER WITH CONVERTER ASSEMBLY

CAUTION:
  1. Be sure to wear insulated gloves.
  2. Do not touch the high-voltage connectors or terminals for 5 minutes after the service plug grip is removed.



    E160581E01
  1. Disconnect the connector from the inverter with converter assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B-3 - 1
    Always
    Below 1 Ω
    B-1 - 2
    Always
    Below 1 Ω



NG
REPLACE INVERTER WITH CONVERTER ASSEMBLY
OK


5.INSPECT NO. 4 ENGINE WIRE


    E109277E11
  1. Disconnect the connector from the No. 4 engine wire.

    CAUTION:
    Be sure to wear insulated gloves.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    i1-1 (-) - i2-1 (-)
    Always
    Below 1 Ω
    i1-2 (+) - i2-3 (+)
    Always
    Below 1 Ω
    i1-1 (-) - i1-3 (+)
    Always
    10 kΩ or higher



NG
REPLACE NO. 4 ENGINE WIRE
OK

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY