DTC B1498/98 Communication Malfunction (A/C Inverter Local) |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1498/98 |
|
|

| 1.CHECK CAN COMMUNICATION SYSTEM |
Using the Techstream, check if the CAN communication system is functioning normally.
| Result | Proceed to |
| CAN DTC is not output | A |
| CAN DTC is output | B |
|
| ||||
| A | |
| 2.CHECK FOR DTC |
Check if DTCs for the hybrid control system are output using the Techstream.
| Result | Proceed to |
| DTC is not output | A |
| Only DTC P3108 is output | A |
| DTCs other than P3108 are output | B |
|
| ||||
| A | |
| 3.INSPECT FUSE (A/C NO. 2) |
Remove the A/C No. 2 fuse from the instrument panel junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Item | Condition | Specified condition |
| A/C No. 2 fuse | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - BODY GROUND) |
![]() |
Disconnect the connector from the compressor with motor assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection (Symbols) | Condition | Specified Condition |
| B48-5 (GND) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (IG1 - GND) |
![]() |
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection (Symbols) | Switch Condition | Specified Condition |
| B48-6 (IG1) - B48-5 (GND) | Power switch on (IG) | 11 to 14 V |
| B48-6 (IG1) - B48-5 (GND) | Power switch off | Below 1 V |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY) |
Disconnect the connector from the hybrid vehicle control ECU.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection (Symbols) | Condition | Specified Condition |
| B48-1 (CLK) - B2-18 (CLK) | Always | Below 1 Ω |
| B48-2 (DIN) - B2-20 (ITE) | Always | Below 1 Ω |
| B48-3 (DOUT) - B2-19 (ETI) | Always | Below 1 Ω |
| B48-1 (CLK) - Body ground | Always | 10 kΩ or higher |
| B48-2 (DIN) - Body ground | Always | 10 kΩ or higher |
| B48-3 (DOUT) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.INSPECT ELECTRIC VEHICLE FUSE |
Turn the power switch off.
Remove the service plug grip.
![]() |
Remove the connector cover assembly.
![]() |
Check that bolts A and B are tightened securely.
Measure the resistance according to the value(s) in the table below.
| Tester Item (Tester Connection) | Condition | Specified Condition |
| ELECTRIC VEHICLE fuse (A - B) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 8.INSPECT INVERTER WITH CONVERTER ASSEMBLY |
![]() |
Disconnect the connector from the inverter with converter assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection (Symbols) | Condition | Specified Condition |
| B-3 - 1 | Always | Below 1 Ω |
| B-1 - 2 | Always | Below 1 Ω |
|
| ||||
| OK | |
| 9.INSPECT NO. 4 ENGINE WIRE |
![]() |
Disconnect the connector from the No. 4 engine wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection (Symbols) | Condition | Specified Condition |
| i1-1 (-) - i2-1 (-) | Always | Below 1 Ω |
| i1-2 (+) - i2-2 (+) | Always | Below 1 Ω |
| i1-1 (-) - i1-2 (+) | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY |
![]() |
Reconnect the connector to the compressor with motor assembly.
Turn the power switch on (IG).
Measure the waveform according to the following tables.
![]() |
CLK - Body ground
| Tester Connection (Symbols) | Switch Condition | Specified Condition |
| B2-18 (CLK) - Body ground | Power switch on (IG) | Pulse generation |
| Item | Contents |
| Tool Setting | 5 V/DIV., 200 ms./DIV. |
| Vehicle Condition | Power switch on (IG) |
![]() |
ITE - Body ground
| Tester Connection (Symbols) | Switch Condition | Specified Condition |
| B-20 (ITE) - Body ground | Power switch on (IG) | Pulse generation |
| Item | Contents |
| Tool Setting | 5 V/DIV., 200 ms./DIV. |
| Vehicle Condition | Power switch on (IG) |
|
| ||||
| OK | ||
| ||