Home › HYBRID SYSTEM ยท P310 › HYBRID VEHICLE CONTROL › WATER PUMP WITH MOTOR

WATER PUMP WITH MOTOR > REMOVAL

for Preparation Click here



1. REMOVE NO. 2 ENGINE ROOM SIDE COVER LH


    A173813
  1. Remove the engine room side cover.



2. DRAIN COOLANT (for Inverter)

NOTICE:
  1. Do not reuse the drained coolant because it may contain foreign objects.
  2. Collect the drained coolant and measure its volume to establish a benchmark. When adding coolant, make sure to add more coolant than the measured amount.

  1. Remove the inverter reserve tank cap.

    CAUTION:
    To avoid the danger of being burned, do not remove the inverter reserve tank cap while the coolant for the inverter is still hot.



    C109300
  1. Using a hexagon wrench (10 mm), remove the drain plug indicated in the illustration and drain the coolant.

    CAUTION:
    Use caution when handling coolant immediately after driving or in summer because it may be hot.

  1. Install the plug with a new gasket.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }



3. REMOVE NO. 1 ENGINE UNDER COVER
  1. Remove the 6 bolts, 2 screws, 2 clips and No. 1 engine under cover.



4. REMOVE COOL AIR INTAKE DUCT SEAL
  1. Remove the 11 clips and cool air intake duct seal.



5. REMOVE RADIATOR GRILLE


    B181108E01
  1. Put protective tape around the radiator grille.



    B181109
  1. Remove the 2 bolts and 4 clips.



    B181110
  1. Disengage the 6 claws and 4 guides, and remove the radiator grille.



6. REMOVE FRONT BUMPER ASSEMBLY (w/o Fog Light)


    B172760E01
  1. Put protective tape around the front bumper assembly.

    HINT:
    Use the same procedure for the RH side and LH side.



    B172761E01
  1. Remove the screw.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.



    B172763
  1. Remove the 7 screws and clip.



    B172764
  1. Disengage the 4 claws and disconnect the front bumper assembly.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Remove the front bumper assembly.



7. REMOVE FRONT BUMPER ASSEMBLY (w/ Fog Light)


    B172760E01
  1. Put protective tape around the front bumper assembly.

    HINT:
    Use the same procedure for the RH side and LH side.



    B172761E01
  1. Remove the screw.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.



    B172763
  1. Remove the 7 screws and clip.



    B172764
  1. Disengage the 4 claws and disconnect the front bumper assembly.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Disconnect each fog light connector, and then remove the front bumper assembly.



8. DRAIN HYBRID TRANSAXLE FLUID


    C173143E01
  1. Using a socket hexagon wrench 10 mm, remove the filler plug and gasket.

  1. Using a socket hexagon wrench 10 mm, remove the drain plug and gasket.

  1. Using a socket hexagon wrench 10 mm, install the drain plug, and a new gasket.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }



9. REMOVE FRAME SIDE RAIL PLATE SUB-ASSEMBLY LH


    A108529
  1. Using a transmission jack, hold the front frame.

    NOTICE:
    Be sure to position the transmission jack to properly support the front frame.

  1. Remove the 3 bolts, nut and frame side rail plate sub-assembly.



10. REMOVE WATER WITH MOTOR AND BRACKET PUMP ASSEMBLY


    A177835
  1. Disconnect the 3 clamps and 2 oil cooler hoses from the oil cooler assembly.



    A175938
  1. Disconnect the connector and 2 water hoses from the water with motor and bracket pump assembly.

  1. Remove the bolt, nut, and water with motor and bracket pump assembly.