Home › BRAKE › PARKING BRAKE › PARKING BRAKE ASSEMBLY

PARKING BRAKE ASSEMBLY > DISASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and the LH side.
  2. The procedures listed below are for the LH side.



1. REMOVE REAR WHEEL


2. REMOVE REAR AXLE SHAFT NUT

NOTICE:
Perform this procedure only when the No. 1 parking brake shoe hold down spring pin is replaced.

HINT:
Click here.



3. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY


    C165996
  1. Remove the 2 bolts and separate the rear disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.



4. REMOVE REAR DISC


    C166438E01
  1. Put matchmarks on the rear disc and the axle hub.



    D028126
  1. Release the parking brake and remove the rear disc.

    HINT:
    If the disc cannot be removed easily, turn and press firmly the shoe adjuster until the wheel comes free.



5. REMOVE NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING


    C166147
  1. Remove the 2 No. 1 parking brake shoe return tension springs.



6. SEPARATE NO. 1 PARKING BRAKE SHOE ASSEMBLY


    C166148
  1. Remove the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring and No. 2 parking brake shoe hold down spring cup, and separate the No. 1 parking brake shoe assembly from the backing plate.



7. REMOVE PARKING BRAKE SHOE STRUT


    C166149
  1. Remove the parking brake shoe strut and the parking brake shoe strut compression spring.



8. SEPARATE NO. 2 PARKING BRAKE SHOE ASSEMBLY


    C166150
  1. Remove the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring and No. 2 parking brake shoe hold down spring cup, and separate the No. 2 parking brake shoe assembly from the backing plate.



9. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET


    C166151
  1. Remove the parking brake shoe adjusting screw set.



10. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY


    C166152
  1. Separate the No. 2 parking brake shoe return tension spring and remove the No. 1 parking brake shoe assembly.



11. REMOVE NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING


    C166153
  1. Remove the No. 2 parking brake shoe return tension spring from the No. 2 parking brake shoe assembly.



12. REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY WITH PARKING BRAKE SHOE LEVER


    C166154
  1. Using needle-nose pliers, separate the No. 3 parking brake cable assembly from the parking brake shoe lever as shown in the illustration.

    NOTICE:
    Be careful not to damage the No. 3 parking brake cable assembly.



13. REMOVE PARKING BRAKE SHOE LEVER


    C166161
  1. Remove the C-washer, shim and the parking brake shoe lever from the No. 2 parking brake shoe assembly.



14. REMOVE PARKING BRAKE SHOE GUIDE PLATE SET BOLT


    C166163
  1. Remove the parking brake shoe guide plate set bolt and the parking brake shoe guide plate.



15. REMOVE NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN


    C166157
  1. Remove the No. 2 parking brake shoe hold down spring pin.



16. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY

NOTICE:
Perform this procedure only when the No. 1 parking brake shoe hold down spring pin is replaced.

HINT:
Click here.



17. REMOVE NO. 1 PARKING BRAKE SHOE HOLD DOWN SPRING PIN


    C168096
  1. Remove the No. 1 parking brake shoe hold down spring pin.