Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0327    Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

DTC    P0328    Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

DTC    P0332    Knock Sensor 2 Circuit Low Input (Bank 2)

DTC    P0333    Knock Sensor 2 Circuit High Input (Bank 2)

for Preparation Click here


DESCRIPTION

A flat type knock sensor (non-resonant type) has the structure that can detect the vibration in a wider band of frequency from about 6 kHz to 15 kHz and has the following features.
Knock sensors are fitted on the right bank and left bank of the cylinder block to detect engine knockings. Each knock sensor contains a piezoelectric element which generates voltage when it becomes deformed. Generation of the voltage occurs when the cylinder block vibrates due to a knocking. If an engine knocking occurs, the ignition timing is retarded in order to suppress the knocking.

DTC No.
DTC Detection Condition
Trouble Area
P0327
P0332
Output voltage of the knock sensor 1 or 2 is 0.5 V or less
(1 trip detection logic)
  1. Short in knock sensor 1 or 2 circuit
  2. Knock sensor 1 or 2
  3. Hybrid vehicle control ECU
P0328
P0333
Output voltage of the knock sensor 1 or 2 is 4.5 V or more
(1 trip detection logic)
  1. Open in knock sensor 1 or 2 circuit
  2. Knock sensor 1 or 2
  3. Hybrid vehicle control ECU
Reference: Inspection using the oscilloscope.
A085286E57

Item
Details
Terminal
KNK1 - EKNK
or
KNK2 - EKN2
Equipment Settings
0.01 to 10 V/Division,
0.01 to 10 msec./Division
Condition
After warming up the engine,
keep the engine speed at 4000 rpm.
The correct waveform is as shown.

MONITOR DESCRIPTION

The knock sensor, located on the cylinder block, detects an engine knocking. When engine knocking occurs, the sensor picks-up vibrates. When the ECM (included in the hybrid vehicle control ECU) detects the voltage in this frequency range, it retards the ignition timing to suppress the engine knocking.
The ECM (included in the hybrid vehicle control ECU) also senses background engine noise with the knock sensor and uses this noise to check for faults in the sensor. If the knock sensor signal level is too low for more than 10 seconds, and if the knock sensor output voltage is out of normal range, the ECM interprets this as a fault in the knock sensor and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0327: Knock sensor (Bank 1) range check (Low voltage)
P0328: Knock sensor (Bank 1) range check (High voltage)
P0332: Knock sensor (Bank 2) range check (Low voltage)
P0333: Knock sensor (Bank 2) range check (High voltage)
Required sensors/components (Main)
Knock sensor (Bank 1 and 2)
Required sensor/components (Related)
Mass air flow meter, Crankshaft position sensor, Camshaft position sensor
Engine coolant temperature sensor
Frequency of operation
Continuous
Duration
1 second
MIL operation
Immediate
Sequence operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None
Battery voltage
10.5 V or more
Time after engine start
5 seconds or more
Power switch
ON

TYPICAL MALFUNCTION THRESHOLDS


P0327, P0332 
Knock sensor voltage
Less than 0.5 V

P0328, P0333 
Knock sensor voltage
More than 4.5 V

WIRING DIAGRAM


A182712E01


INSPECTION PROCEDURE

HINT:
  1. DTCs P0327 and P0328 are for the bank 1 knock sensor circuit.
  2. DTCs P0332 and P0333 are for the bank 2 knock sensor circuit.
  3. Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.READ OUTPUT DTC (CHECK KNOCK SENSOR CIRCUIT)


    A079805E05
  1. Disconnect the Bd1 connector.

  1. Using lead wires, connect the Bd1 terminals as follows.
    Male Connector - Female Connector
    Terminal 2 - Terminal 4
    Terminal 1 - Terminal 3
    Terminal 4 - Terminal 2
    Terminal 3 - Terminal 1

  1. Warm up the engine.

  1. Run the engine at 2500 rpm for 10 seconds or more.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Select the items: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:
    Display
    Proceed to
    DTCs same as when vehicle brought in
    P0327, P0328 → P0327, P0328
    or
    P0332, P0333 → P0332, P0333
    A
    DTCs different from when vehicle brought in
    P0327, P0328 → P0332, P0333
    or
    P0332, P0333 → P0327, P0328
    B

  1. Reconnect the Bd1 connector.



B
Go to step 4
A


2.CHECK HARNESS AND CONNECTOR (Bd1 CONNECTOR - HYBRID VEHICLE CONTROL ECU)


    A178446E02
  1. Disconnect the Bd1 connector.



    A178447E07
  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    Bd1 female connector 2 - B2-29 (KNK1)
    Always
    Below 1 Ω
    Bd1 female connector 1 - B2-28 (EKNK)
    Always
    Bd1 female connector 4 - B2-21 (KNK2)
    Always
    Bd1 female connector 3 - B2-20 (EKN2)
    Always

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    Bd1 female connector 2 or B2-29 (KNK1) - Body ground
    Always
    10 kΩ or higher
    Bd1 female connector 1 or B2-28 (EKNK) - Body ground
    Always
    Bd1 female connector 4 or B2-21 (KNK2) - Body ground
    Always
    Bd1 female connector 3 or B2-20 (EKN2) - Body ground
    Always

  1. Reconnect the Bd1 connector.

  1. Reconnect the hybrid vehicle control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (Bd1 CONNECTOR KNOCK - CONTROL SENSOR)
OK


3.CHECK HYBRID VEHICLE CONTROL ECU


    A178447E07
  1. Disconnect the hybrid vehicle control ECU connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    B2-29 (KNK1) - B2-28 (EKNK)
    Power switch on (IG)
    4.5 to 5.5 V
    B2-21 (KNK2) - B2-20 (EKN2)
    Power switch on (IG)

  1. Reconnect the hybrid vehicle control ECU connector.



NG
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.CHECK KNOCK CONTROL SENSOR (SENSOR RESISTANCE)


    A114618E14
  1. Disconnect the Bd1 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Bd1 male connector 2 - 1
    Always
    120 to 280 kΩ
    Bd1 male connector 4 - 3
    Always

  1. Reconnect the Bd1 connector.



NG
Go to step 5
OK


5.CHECK HARNESS AND CONNECTOR (Bd1 CONNECTOR - KNOCK CONTROL SENSOR)

HINT:
  1. If DTC P0327 or P0328 has changed to P0332 or P0333, check the knock sensor circuit on the right bank side.
  2. If DTC P0332 or P0333 has changed to P0327 or P0328, check the knock sensor circuit on the left bank side.



    A114618E14
  1. Disconnect the Bd1 connector.

  1. Disconnect the d1 or d2 knock sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    Bd1 male connector 2 - d1-2
    Always
    Below 1 Ω
    Bd1 male connector 1 - d1-1
    Always
    Bd1 male connector 4 - d2-2
    Always
    Bd1 male connector 3 - d2-1
    Always

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    Bd1 male connector 2 - d1-2 or Body ground
    Always
    10 kΩ or higher
    Bd1 male connector 1 - d1-1 or Body ground
    Always
    Bd1 male connector 4 - d2-2 or Body ground
    Always
    Bd1 male connector 3 or d2-1 - Body ground
    Always

  1. Reconnect the Bd1 connector.

  1. Reconnect the knock sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (Bd1 CONNECTOR KNOCK - CONTROL SENSOR)
OK

REPLACE KNOCK CONTROL SENSOR (Click here)