Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P011B    Engine Coolant Temperature / Intake Air Temperature Correlation

for Preparation Click here


DESCRIPTION

The engine has two temperature sensors, an engine coolant temperature sensor and an intake air temperature sensor, to detect the temperature while the engine is in operation. A thermistor, whose resistance value varies according to the temperature, is built into each sensor. When the temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM (included in the hybrid vehicle control ECU) as voltage changes. Based on these temperature signals output from the sensors, the ECM determines the fuel injection time and the ignition timing to control the engine.

DTC No.
DTC Detection Condition
Trouble Area
P011B
  1. All of following conditions are met:
    (2 trip detection logic)
    1. Battery voltage 10.5 V or more
    2. 7 hours or more elapsed from engine stops on previous trip
    3. 15 seconds after cold engine starts
    4. Minimum intake air temperature after engine starts at more than -10°C (14°F)
    5. Average engine coolant temperature before engine starts at more than -10°C (14°F)
    6. Difference between readings of engine coolant temperature and intake air temperature greater than 20°C (36°F)
  1. Intake air temperature sensor
  2. Engine coolant temperature sensor
  3. Hybrid vehicle control ECU

A178409E04

HINT:
  1. Waiting is required to prevent the temperature of the engine from affecting the readings. If the engine has been operated recently, it will not be possible to accurately compare the readings.
  1. For diagnosis, in order to duplicate the detection conditions of the DTC, it is necessary to park the vehicle for 7 hours. Parking the vehicle for 7 hours ensures that the actual temperature of the engine coolant temperature and intake air temperature are very similar. If the vehicle has been parked for less than 7 hours, differences in the readings may exist, this does not necessarily indicate a fault.


MONITOR DESCRIPTION

The ECM monitors the difference between the engine coolant temperature and the intake air temperature when the engine is started cold to detect the engine temperature conditions accurately. The monitor runs when the engine started cold after 7 hours or more has elapsed since the engine was stopped (power switch turned off) on the previous trip. If the difference between the engine coolant temperature and the intake air temperature on a cold start exceeds 20°C (36°F), the ECM interprets this as a malfunction in the engine coolant temperature sensor circuit and intake air temperature sensor circuit, and sets the DTC.

MONITOR STRATEGY


Related DTCs
P011B: engine coolant temperature / intake air temperature sensor correlation
Required Sensors / Components (Main)
Engine coolant temperature / intake air temperature sensor
Required Sensors / Components (Related)
-
Frequency of Operation
Once per driving cycle
Duration
7 hours or more
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not present
None
All of the following conditions are met
Conditions 1 and 2
1. All of the following conditions are met
Conditions (a), (b), (c) and (d)
(a) After power switch on (IG) and engine not running time
Less than 20 seconds
(b) Soak time
7 hours or more
(c) Battery voltage
10.5 V or more
(d) Time after engine start
76 seconds or more
2. Either of the following conditions is met
Conditions (a) and (b)
(a) Minimum intake air temperature after engine start
-10°C (14°F) or more
(b) Engine coolant temperature before engine start
-10°C (14°F) or more

TYPICAL MALFUNCTION THRESHOLDS


Deviated engine coolant temperature and intake air temperature
Less than -20°C (-36°F) or more than 20°C (36°F)

INSPECTION PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P011B)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Select the following menu items:

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    P011B
    A
    P011B and other DTCs
    B

    HINT:
    If any DTCs other than P011B are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (INTAKE AIR TEMPERATURE)
  1. Leave the vehicle for 7 hours or more.

    HINT:
    It is necessary to leave the vehicle for 7 hours or more to duplicate the DTC detection conditions.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the Techstream.

    OK:
    The difference between the intake air temperature and the actual outside air temperature is within 10°C (18°F).

    HINT:
    Temperature readings on the vehicle's outside temperature gauge (if equipped) are not suitable for comparing to the intake air temperature reading. The outside temperature gauge has a significant delay built in to prevent temperature swings from being displayed on its display. Use an accurate thermometer to determine the outside air temperature.



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


3.READ VALUE USING TECHSTREAM (COOLANT TEMPERATURE)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the Techstream.

    OK:
    The difference between the coolant temperature and the actual outside air temperature is within 10°C (18°F).

    HINT:
    If the result is not as specified, check that there are heat sources such as a block heater in the engine compartment.



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)