Terminal No. (Symbols)
| Wiring Color
| Terminal Description
| Condition
| Specification
|
a3-1 (+B) - a3-3 (GND)
| R - W-B
| Battery
| Always
| 10 to 14 V
|
a3-2 (DIA) - a3-3 (GND)
| GR - W-B
| Diagnosis (DLC3)
| power switch on (IG)
| Pulse generation
|
a3-3 (GND) - Body ground
| W-B - Body ground
| Ground
| Always
| Below 1 V
|
a3-4 (FSR-) - a3-3 (GND)
| B - W-B
| Center airbag sensor assembly communication line (-)
| Always
| Below 1 V
|
a3-5 (BGND) - a3-3 (GND)
| P - W-B
| Passenger side buckle switch ground line
| Always
| Below 1 V
|
a3-7 (IG) - a3-3 (GND)
| BR - W-B
| Power source (ECU-B fuse)
| power switch on (IG)
| 10 to 14 V
|
a3-8 (FSR+) - a3-4 (FSR-)
| W - B
| Center airbag sensor assembly communication line
| power switch on (IG)
| Pulse generation
|
a3-9 (BSW) - a3-5 (BGND)
| L - P
| Passenger side buckle switch line
| Always
| Below 1 V
|
a1-1 (SGD1) - a3-3 (GND)
| G - W-B
| Front occupant classification sensor LH ground line
| Always
| Below 1 V
|
a1-2 (SGD2) - a3-3 (GND)
| O - W-B
| Front occupant classification sensor RH ground line
| Always
| Below 1 V
|
a1-3 (SGD3) - a3-3 (GND)
| LG - W-B
| Rear occupant classification sensor LH ground line
| Always
| Below 1 V
|
a1-4 (SGD4) - a3-3 (GND)
| BR - W-B
| Rear occupant classification sensor RH ground line
| Always
| Below 1 V
|
a1-5 (SVC3) - a1-3 (SGD3)
| GR - LG
| Rear occupant classification sensor LH power supply line
| power switch on (IG), a load is applied to rear occupant classification sensor LH
| 4.5 to 5.1 V
|
a1-6 (SVC4) - a1-4 (SGD4)
| V - BR
| Rear occupant classification sensor RH power supply line
| power switch on (IG), a load is applied to rear occupant classification sensor RH
| 4.5 to 5.1 V
|
a1-7 (SIG1) - a1-1 (SGD1)
| P - G
| Front occupant classification sensor LH signal line
| power switch on (IG), a load is applied to front occupant classification sensor LH
| 0.2 to 4.9 V
|
a1-8 (SIG2) - a1-2 (SGD2)
| L - O
| Front occupant classification sensor RH signal line
| power switch on (IG), a load is applied to front occupant classification sensor RH
| 0.2 to 4.9 V
|
a1-9 (SIG3) - a1-3 (SGD3)
| Y - LG
| Rear occupant classification sensor LH signal line
| power switch on (IG), a load is applied to rear occupant classification sensor LH
| 0.2 to 4.9 V
|
a1-10 (SIG4) - a1-4 (SGD4)
| B - BR
| Rear occupant classification sensor RH signal line
| power switch on (IG), a load is applied to rear occupant classification sensor RH
| 0.2 to 4.9 V
|
a1-11 (SVC1) - a1-1 (SGD1)
| R - G
| Front occupant classification sensor LH power supply line
| power switch on (IG), a load is applied to front occupant classification sensor LH
| 4.5 to 5.1 V
|
a1-12 (SVC2) - a1-2 (SGD2)
| W - O
| Front occupant classification sensor RH power supply line
| power switch on (IG), a load is applied to front occupant classification sensor RH
| 4.5 to 5.1 V
|