Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

OCCUPANT CLASSIFICATION SYSTEM > Trouble in Passenger Airbag ON/OFF Indicator

for Preparation Click here


DESCRIPTION

The occupant classification system detects the front passenger seat condition. It then informs a passenger of the front passenger airbag assembly and front seat side airbag assembly RH condition (activated/not activated) with the passenger airbag ON/OFF indicator.

HINT:
Approximately 6 seconds after the power switch is turned on (IG), the passenger airbag ON/OFF indicator will be ON/OFF depending on the conditions listed below.


Front Passenger Seat Condition
Passenger Airbag ON/OFF Indicator
SRS Warning Light
ON Indicator
OFF Indicator
Vacant
OFF
OFF
OFF
Adult is seated.
ON
OFF
OFF
Child is seated.
OFF
ON
OFF
Child restraint system is set.
OFF
ON
OFF
Occupant classification system failure
OFF
ON
ON

INSPECTION PROCEDURE

1.CHECK SRS WARNING LIGHT
  1. Turn the power switch on (IG), and check the SRS warning light condition.

    HINT:
    If this trouble occurs, the SRS warning light is off. If the light is on, a DTC is output. Troubleshoot for the output DTC.

    OK:
    After the primary check period, the SRS warning light goes off.

    HINT:
    The primary check is performed for approximately 6 seconds after the power switch is turned on (IG).



NG
GO TO DTC CHART (Click here)
OK


2.PERFORM ZERO POINT CALIBRATION
  1. Turn the power switch off.

  1. Connect Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Using Techstream, perform "zero point calibration" (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.



NG
Go to step 4
OK


3.PERFORM SENSITIVITY CHECK
  1. Using Techstream, perform "sensitivity check" (Click here).

    Standard:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 4
OK

END 

4.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
  1. Turn the power switch off.

  1. Loosen the 4 installation bolts of the front seat assembly RH.

  1. Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.

Torque:
37 N*m{ 377 kgf*cm , 27 ft.*lbf }


NEXT


5.PERFORM ZERO POINT CALIBRATION
  1. Connect Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Using Techstream, perform "zero point calibration" (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.



NG
Go to step 7
OK


6.PERFORM SENSITIVITY CHECK
  1. Using Techstream, perform "sensitivity check" (Click here).

    Standard:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 7
OK

END 

7.READ VALUE USING PASSENGER SIDE BUCKLE SWITCH
  1. Turn the power switch on (IG).

  1. Using Techstream, read the "Data List" (Click here).

    1. Read the display when the passenger side buckle switch is operated.

      Occupant Detection: 
      Tester Display
      Measurement Item / Range
      Normal Condition
      Diagnostic Note
      Passenger Buckle SW
      Passenger side buckle switch/
      Set: The seat belt is fastened
      Unset: The seat belt is not fastened
      NG: Data is not determined
      Unset/Set
      -

OK:
The Techstream display changes correctly in accordance with the operation of the buckle switch.



NG
Go to step 12
OK


8.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Disconnect the connectors from the occupant classification ECU and the 4 occupant classification sensors.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FRONT SEAT WIRE RH
OK


9.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Connect the connectors to the 4 occupant classification sensors.

  1. Replace the occupant classification ECU (Click here).


NEXT


10.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Using Techstream, perform "zero point calibration" (Click here).

OK:
"Zero Point Calibration is complete." is displayed.


NEXT


11.PERFORM SENSITIVITY CHECK
  1. Using Techstream, perform "sensitivity check" (Click here).

    Standard:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

END 

12.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Disconnect the connectors from the occupant classification ECU and the front seat inner belt assembly RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FRONT SEAT WIRE RH
OK


13.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
  1. Connect the connector to the occupant classification ECU.

  1. Replace the front seat inner belt assembly RH (Click here).


NEXT


14.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Using Techstream, perform "zero point calibration" (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


15.PERFORM SENSITIVITY CHECK
  1. Using Techstream, perform "sensitivity check" (Click here).

    Standard:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

END