FRONT SHOCK ABSORBER > INSTALLATION |
| 1. SECURE FRONT SHOCK ABSORBER ASSEMBLY |
![]() |
As shown in the illustration, secure the front shock absorber with coil spring in a vise using aluminum plates by clamping onto a double nutted bolt affixed to the bracket at the bottom of the absorber.
| 2. INSTALL FRONT COIL SPRING LOWER INSULATOR |
![]() |
Install the front coil spring lower insulator to the front shock absorber.
| 3. INSTALL FRONT SPRING BUMPER |
![]() |
Install the front spring bumper to the front shock absorber.
| 4. INSTALL FRONT COIL SPRING |
![]() |
Using SST, compress the front coil spring.
![]() |
Install the front coil spring to the front shock absorber.
| 5. INSTALL FRONT COIL SPRING UPPER INSULATOR |
![]() |
Install the front coil spring upper insulator as shown in the illustration.
| 6. INSTALL FRONT COIL SPRING UPPER SEAT |
![]() |
Install the front coil spring upper seat with the mark facing to the outside of the vehicle.
| 7. INSTALL FRONT SUSPENSION SUPPORT BEARING |
![]() |
Install the front suspension support bearing as shown in the illustration.
| 8. INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY |
![]() |
Install the front suspension support sub-assembly as shown in the illustration.
Temporarily tighten a new front support to front shock absorber nut.
| 9. INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING |
![]() |
Install the front shock absorber with coil spring (upper side) with the nut and 2 spacers.
![]() |
Install the front shock absorber with coil spring (lower side) to the steering knuckle and insert the 2 bolts and 2 nuts.
| 10. INSTALL FRONT STABILIZER LINK ASSEMBLY |
![]() |
Install the front stabilizer link assembly to the front shock absorber with the nut.
| 11. INSTALL FRONT SPEED SENSOR |
![]() |
Install the front speed sensor and front flexible hose with the bolt.
Install the clamp.
| 12. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY |
![]() |
Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.
![]() |
Engage the 4 clamps.
| 13. FULLY TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT |
![]() |
Fully tighten the front support to front shock absorber nut.
| 14. INSTALL WINDSHIELD WIPER MOTOR AND LINK |
![]() |
Install the windshield wiper motor and link assembly with the 4 bolts.
Connect the connector.
| 15. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
Engage the 20 claws.

Install the cowl top ventilator louver sub-assembly with the 2 clips.
![]() |
Engage the 2 claws and connect the front fender to cowl side seal LH.
![]() |
Engage the 2 claws and connect the front fender to cowl side seal RH.
| 16. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
When reinstalling:
![]() |
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 25.6 mm (1.00 in.) |
| 17. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
When reinstalling:
![]() |
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 31.9 mm (1.26 in.) |
Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.
| 18. INSTALL FRONT WHEEL |
| 19. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |