Home › SUSPENSION & AXLE › SUSPENSION › FRONT SHOCK ABSORBER

FRONT SHOCK ABSORBER > REMOVAL

for Preparation Click here



1. REMOVE FRONT WHEEL


2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E150144
  1. Remove the nut, and the front wiper arm and blade assembly LH.



3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E150145
  1. Remove the nut, and the front wiper arm and blade assembly RH.



4. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E150146
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal LH.



    E150147
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal RH.



  1. Remove the 2 clips.


    E150149

  1. Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.



5. LOOSEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT


    C165911
  1. Loosen the front support to front shock absorber nut of the front shock absorber.

    NOTICE:
    1. Do not remove the front support to front shock absorber nut.
    2. Loosen the nut only when the front shock absorber with coil spring needs to be disassembled.



6. REMOVE WINDSHIELD WIPER MOTOR AND LINK


    E150150
  1. Disconnect the connector.

  1. Remove the 4 bolts, and the windshield wiper motor and link assembly.



7. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY


    C175029
  1. Disengage the 4 clamps and separate the wiper wire harness from the outer cowl top panel sub-assembly.



    C175030
  1. Remove the 8 bolts, 6 nuts, and the outer cowl top panel sub-assembly.



8. SEPARATE FRONT SPEED SENSOR


    C167708
  1. Remove the bolt and clamp, and separate the front speed sensor and front flexible hose.



9. SEPARATE FRONT STABILIZER LINK ASSEMBLY


    C165915
  1. Remove the nut and separate the front stabilizer link assembly from the front shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.



10. REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING


    C165927E01
  1. Support the front axle using a jack and wooden block.



    C165908
  1. Remove the 2 bolts and 2 nuts, and separate the front shock absorber with coil spring (lower side) from the steering knuckle.

    NOTICE:
    Keep the bolts from rotating when removing the nuts.



    C165912
  1. Remove the nut and 2 spacers on the upper side of the front shock absorber with coil spring.

    NOTICE:
    Make sure that the front speed sensor is completely separated from the front shock absorber with coil spring.



11. SECURE FRONT SHOCK ABSORBER WITH COIL SPRING


    C166280E01
  1. As shown in the illustration, secure the front shock absorber with coil spring in a vise using aluminum plates by clamping onto a double nutted bolt affixed to the bracket at the bottom of the absorber.



12. REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT


    C166281E01
  1. Using SST, compress the front coil spring.

    SST
    09727-30021   (09727-00010, 09727-00031)
    09727-00050  

    NOTICE:
    Do not use an impact wrench. It will damage SST.

    HINT:
    If the front coil spring is compressed at an angle, using 2 SST will make the work easier.

  1. Check that the front coil spring is sufficiently compressed.



    C149544
  1. Remove the front support to front shock absorber nut.



13. REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY


14. REMOVE FRONT SUSPENSION SUPPORT BEARING


15. REMOVE FRONT COIL SPRING UPPER SEAT


16. REMOVE FRONT COIL SPRING UPPER INSULATOR


17. REMOVE FRONT COIL SPRING


18. REMOVE FRONT SPRING BUMPER


19. REMOVE FRONT COIL SPRING LOWER INSULATOR


20. REMOVE FRONT SHOCK ABSORBER ASSEMBLY