Home › SUSPENSION & AXLE › SUSPENSION › REAR SHOCK ABSORBER

REAR SHOCK ABSORBER > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. REMOVE REAR WHEEL


2. REMOVE DECK SIDE TRIM COVER


    B173595E01
  1. Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE DECK SIDE TRIM


    B173596
  1. Remove the bolt.



    B173623
  1. Disengage the 4 claws and the 3 guides, and remove the deck side trim LH as shown in the illustration.



4. SEPARATE REAR FLEXIBLE HOSE


    C166009
  1. Remove the bolt and separate the rear flexible hose from the rear shock absorber with coil spring.



5. SEPARATE REAR SPEED SENSOR


    C166254
  1. Remove the bolt and separate the rear speed sensor from the rear shock absorber with coil spring.



6. SEPARATE REAR STABILIZER LINK ASSEMBLY


    C166214E01
  1. Remove the nut and separate the rear stabilizer link assembly from the rear shock absorber with coil spring.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.



7. REMOVE REAR NO. 1 SUSPENSION SUPPORT COVER


    C166225
  1. Disengage the 4 claws and remove the rear No. 1 suspension support cover.



8. REMOVE REAR SHOCK ABSORBER WITH COIL SPRING


    C166004E01
  1. Using a jack and wooden block, support the rear axle carrier sub-assembly.

    NOTICE:
    Do not deform the dust cover.

    HINT:
    Support the rear axle carrier sub-assembly until reinstallation of the rear shock absorber with coil spring is complete.



    C166011
  1. Loosen the rear support to rear shock absorber nut.

    CAUTION:
    Do not remove the rear support to rear shock absorber nut.

    NOTICE:
    Loosen the nut only when the rear shock absorber with coil spring needs to be disassembled.



    C166010
  1. Remove the 2 bolts and 2 nuts, and separate the rear shock absorber with coil spring from the rear axle carrier sub-assembly.

    NOTICE:
    Keep the bolts from rotating when removing the nuts.



    C166012
  1. Remove the 3 nuts and rear shock absorber with coil spring.

    NOTICE:
    Make sure that the rear speed sensor and rear flexible hose are disconnected from the rear shock absorber with coil spring.



9. SECURE REAR SHOCK ABSORBER WITH COIL SPRING


    C166243E01
  1. Install the bolt and nut to the rear shock absorber with coil spring as shown in the illustration and secure the rear shock absorber with coil spring in a vise.

    Length (A):
    28 mm (1.1 in.)



10. REMOVE REAR SUPPORT TO REAR SHOCK ABSORBER NUT


  1. Using SST, compress the rear coil spring.


    C166013E01

    SST
    09727-30021   (09727-00010, 09727-00021, 09727-00031)

    NOTICE:
    Do not use an impact wrench. It will damage SST.

  1. Check that the front coil spring is fully compressed.



    C166016
  1. Hold the rear suspension support assembly and remove the rear support to rear shock absorber nut from the rear shock absorber assembly.



11. REMOVE REAR SUPPORT TO REAR SHOCK ABSORBER COLLAR


    C166017
  1. Remove the rear support to rear shock absorber collar from the rear shock absorber assembly.



12. REMOVE REAR SUSPENSION SUPPORT ASSEMBLY


    C166018
  1. Remove the rear suspension support assembly from the rear shock absorber assembly.



13. REMOVE REAR COIL SPRING


    C166019
  1. Remove the rear coil spring together with SST from the rear shock absorber assembly.



14. REMOVE REAR NO. 1 SPRING BUMPER


    C166020
  1. Remove the rear No. 1 spring bumper from the rear shock absorber assembly.



15. REMOVE REAR LOWER COIL SPRING INSULATOR


    C166021
  1. Remove the rear lower coil spring insulator from the rear shock absorber assembly.