Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Front Fog Light Circuit

for Preparation Click here


DESCRIPTION

The main body ECU controls the front fog light relay when a signal is received from the headlight dimmer switch assembly.

WIRING DIAGRAM


E121495E08


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. Check the operation.

    Main Body: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Front Fog Light Relay
    Front fog light relay
    ON/OFF
    -

    OK:
    Front fog light relay operates. (Front fog lights come on.)



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FUSE (FR FOG)
  1. Remove the FR FOG fuse from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    FR FOG fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


3.INSPECT FOG LIGHT RELAY (FOG)


    B060778E87
  1. Remove the front fog light relay from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Apply the battery voltage between terminals 1 and 2
    Below 1 Ω



NG
REPLACE FOG LIGHT RELAY
OK


4.CHECK HARNESS AND CONNECTOR (BATTERY - FRONT FOG LIGHT RELAY)


    E151662E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Front fog light relay terminal 5 - Body ground
    Always
    11 to 14 V
    Front fog light relay terminal 1 - Body ground
    Light control switch OFF → TAIL
    Below 1 V → 11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (FRONT FOG LIGHT RELAY - MAIN BODY ECU)


  1. Disconnect the D8 main body ECU connector.


    E151660E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Front fog light relay terminal 2 - D8-4 (FFGO)
    Always
    Below 1 Ω
    D8-4 (FFGO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)


  1. Reconnect the D8 main body ECU connector.


    E142675E01

  1. Install the front fog light relay to the instrument panel junction block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D8-4 (FFGO) - Body ground
    Light control switch in HEAD, front fog light switch OFF → ON
    11 to 14 V → Below 1 V



NG
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT FOG LIGHT RELAY - BODY GROUND)