CYLINDER BLOCK > REASSEMBLY |
| 1. INSTALL STUD BOLTS |
Using E8 and E10 "TORX" sockets, install the stud bolts.

| 2. INSTALL STRAIGHT PINS |
Using a plastic-faced hammer, tap in the straight pins.

| 3. INSTALL RING PINS |
Using a plastic-faced hammer, tap in a new ring pins.

| 4. INSTALL CONNECTING ROD SMALL END BUSH |
![]() |
Align the oil holes of a new bushing and the connecting rod.
![]() |
Using SST and a press, press in the bushing.
![]() |
Using a pin hole grinder, hone the bushing to obtain the standard specified clearance between the bushing and piston pin.
![]() |
Check the piston pin fit at normal room temperature, coat the piston pin with engine oil, and push it into the connecting rod with your thumb.
| 5. INSTALL PISTON PIN HOLE SNAP RING |
![]() |
Using a screwdriver, install a new snap ring at one end of the piston pin hole.
![]() |
Gradually heat the piston to about 80°C (176°F).
Coat the piston pin with engine oil.
![]() |
Align the front marks of the piston and connecting rod, and push in the piston pin with your thumb until the pin contacts the snap ring.
![]() |
Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.
![]() |
Using a screwdriver, install a new snap ring on the other end of the piston pin hole.
| 6. INSTALL PISTON RING SET |
Install the oil ring expander by hand.
Using a piston ring expander, install the oil ring side rail.
![]() |
Using a piston ring expander, install the 2 compression rings.
![]() |
Position the piston rings so that the ring ends are arranged as shown in the illustration.
| 7. INSTALL CONNECTING ROD BEARING |
![]() |
Align the key of the bearing with the keyway of the connecting rod or connecting cap.
| 8. INSTALL CRANKSHAFT BEARING |
![]() |
Clean each main journal and the bearing.
![]() |
Align the key of the bearing with the keyway of the cylinder block, and push in the 4 upper bearings.
![]() |
Align the key of the bearing with the keyway of the main bearing cap, and push in the 4 lower bearings.
| 9. INSTALL CRANKSHAFT THRUST WASHER SET |
![]() |
Install the 2 thrust washers under the No. 2 journal position of the cylinder block with the oil grooves facing outward.
![]() |
Install the 2 thrust washers on the No. 2 bearing cap with the grooves facing outward.
| 10. INSTALL CRANKSHAFT |
Apply engine oil to the upper bearing and install the crankshaft on the cylinder block.
![]() |
Examine the front marks and numbers and install the bearing caps on the cylinder block.
Apply a light coat of engine oil to the threads of the bearing cap bolts.
Temporarily install the 8 main bearing cap bolts to the inside positions.
![]() |
Install the main bearing cap by hand until clearance between the cylinder block and the bearing cap becomes 6 mm (0.23 in.) or less.
![]() |
Using a plastic-faced hammer, lightly tap the bearing cap to ensure a proper fit.
Apply a light coat of engine oil to the threads of the main bearing cap bolts.
![]() |
Using several steps, install and tighten the 16 main bearing cap bolts uniformly in the sequence shown in the illustration.
![]() |
Mark the front side of the bearing cap bolts with paint.
Retighten the bearing cap bolts by 90° in the same sequence as step (h).
![]() |
Check that each painted mark is now at 90° angle to the front.
Check that the crankshaft turns smoothly.
![]() |
Using several steps, install and tighten the 8 main bearing cap bolts and 8 new seal washers uniformly in the sequence shown in the illustration.
| 11. INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD |
Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.
![]() |
Check the position of the piston ring ends.
![]() |
Using a piston ring compressor, push the correctly numbered piston and connecting rod assemblies into each cylinder with the front mark of the piston facing forward.
![]() |
Check that the protrusion of the connecting rod cap is facing the correct direction.
Apply a light coat of engine oil to the threads of the connecting rod cap bolts.
![]() |
Tighten the bolts in several steps to the specified torque.
![]() |
Mark the front side of each connecting cap bolt with paint.
Retighten the cap bolts by 90° as shown in the illustration.
![]() |
Check that the crankshaft turns smoothly.
| 12. INSTALL NO. 3 CYLINDER BLOCK WITH HEAD STRAIGHT SCREW PLUG |
![]() |
Using a 10 mm socket hexagon wrench, install a new gasket and the screw plug.
| 13. INSTALL NO. 2 CYLINDER BLOCK WITH HEAD STRAIGHT SCREW PLUG |
![]() |
Using a 10 mm socket hexagon wrench, install a new gasket and the screw plug.
| 14. INSTALL NO. 1 CYLINDER BLOCK WITH HEAD STRAIGHT SCREW PLUG |
![]() |
Using a 10 mm socket hexagon wrench, install a new gasket and the screw plug.
| 15. INSTALL WATER SEAL PLATE |
Remove any old seal packing from the contact surface.
![]() |
Apply a continuous bead of seal packing (Diameter 4 to 5 mm (0.16 to 0.20 in.)) as shown in the illustration.
Install the seal plate with the 2 nuts.
| 16. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY |
Apply adhesive to 2 or 3 threads of the drain cock end.
![]() |
After applying the specified torque, rotate the drain cock clockwise as shown in the illustration.