Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the radio receiver and steering pad switch illumination when the light control switch is in the TAIL or HEAD position.

WIRING DIAGRAM


E129789E07


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the supplemental restraint system (Click here).

1.CHECK ILLUMINATION
  1. Check if the illumination for the radio receiver, steering pad switch, glove box or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.

    Result:

    Result
    Proceed to
    Illumination comes on for all components except steering pad switch.
    A
    Illumination comes on for all components except radio receiver.
    B
    No illumination comes on (radio receiver, hazard switch, glove box, etc.).
    C
    Illumination comes on only for glove box and steering pad switch.
    D



B
Go to step 6

C
GO TO LIGHTING SYSTEM (Click here)

D
GO TO METER / GAUGE SYSTEM (Click here)
A


2.CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE)


    E126428E09
  1. Disconnect the spiral cable connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D16-12 (IL+2) - Body ground
    Light control SW TAIL or HEAD
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Disconnect the steering pad switch connector.



  1. Connect the positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the steering pad switch assembly connector.


    E152198E03

  1. Check if the illumination for the steering pad switch assembly comes on.

    OK:
    Illumination for the steering pad switch assembly comes on.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY
OK


4.INSPECT SPIRAL CABLE


    I039337E88
  1. Disconnect the steering pad switch and the spiral cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Spiral Cable Position
    Specified Condition
    z2-8 (EAU) - D16-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z2-5 (IL+2) - D16-12 (IL+2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets.

    HINT:
    1. REMOVAL (Click here)
    2. INSTALLATION (Click here)



NG
REPLACE SPIRAL CABLE
OK


5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)


    E141021E12
  1. Disconnect the connectors from the radio receiver and spiral cable.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E3-6 (SWG) - D16-4 (EAU)
    Always
    Below 1 Ω
    E3-6 (SWG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.CHECK HARNESS AND CONNECTOR (BATTERY - RADIO RECEIVER)


    I101969E08
  1. Disconnect the radio receiver connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E2-2 (ILL+) - Body ground (*1)
    Light control switch TAIL or HEAD
    11 to 14 V
    E8-10 (ILL+) - Body ground (*2)
    Light control switch TAIL or HEAD
    11 to 14 V

    HINT:
    1. *1: for Premium models
    2. *2: for Standard models



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - COMBINATION METER)


    I101970E05
  1. Disconnect the radio receiver connector and the combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E2-12 (ILL-) - E1-30 (ILL-) (*1)
    Always
    Below 1 Ω
    E9-5 (ILL-) - E1-30 (ILL-) (*2)
    Always
    Below 1 Ω
    E1-40 (E2) - Body ground
    Always
    Below 1 Ω
    E1-30 (ILL-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. *1: for Premium models
    2. *2: for Standard models



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)