Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > TERMINALS OF ECU

for Preparation Click here



COMBINATION METER ASSEMBLY

E146919E01


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E1-1 (IG+) - Body ground
O - Body ground
Ignition switch signal
Power switch off
Below 1 V
Power switch on (READY)
11 to 14 V
E1-2 (B) - Body ground
G - Body ground
Turn indicator light signal
Power switch on (READY), turn signal LH indicator light OFF
Below 1 V
Power switch on (READY), turn signal LH indicator light ON
11 to 14 V
E1-3 (B) - Body ground
GR - Body ground
Turn indicator light signal
Power switch on (READY), turn signal RH indicator light OFF
Below 1 V
Power switch on (READY), turn signal RH indicator light ON
11 to 14 V
E1-4 (SW1) - Body ground
B - Body ground
Light control rheostat signal (Tail cancel switch)
Power switch on (READY), turn the light control rheostat knob fully downwards (Tail cancel off)
Below 1 V
Power switch on (READY), turn the light control knob rheostat fully upwards (Tail cancel on)
4 to 6 V
E1-8 (WLVL) - Body ground
P - Body ground
Washer level warning light signal
Power switch on (READY), WASHER warning light OFF
11 to 14 V
Power switch on (READY), WASHER warning light ON
Below 1.5 V
E1-9 (+S) - Body ground
LG - Body ground
Speed signal for other system (Output)
Turn a drive wheel slowly
Pulse generation
(See waveform)
E1-10 (CHK) - Body ground
G - Body ground
MIL (Check engine warning light) signal
Power switch on (READY), MIL ON
Below 1 V
Power switch on (READY), MIL OFF
11 to 14 V
E1-12 (FUW1) - Body ground
L - Body ground
Multi-information display signal
Combination meter displays "PLEASE WAIT NOW OPENING" in the multi-information display
11 to 14 V
E1-13 (FUC1) - Body ground
LG - Body ground
Multi-information display signal
Below 1 V
E1-12 (FUW1) - Body ground
L - Body ground
Multi-information display signal
Combination meter displays "REFUEL READY" in the multi-information display
Below 1 V
E1-13 (FUC1) - Body ground
LG - Body ground
Multi-information display signal
Below 1 V
E1-12 (FUW1) - Body ground
L - Body ground
Multi-information display signal
Combination meter displays "CLOSE FUEL LID" in the multi-information display
Below 1 V
E1-13 (FUC1) - Body ground
LG - Body ground
Multi-information display signal
11 to 14 V
E1-12 (FUW1) - Body ground
L - Body ground
Multi-information display signal
Combination meter displays "OFF" in the multi-information display
11 to 14 V
E1-13 (FUC1) - Body ground
LG - Body ground
Multi-information display signal
11 to 14 V
E1-14 (MSSL) - Body ground
P - Body ground
Steering pad switch signal
Power switch on (READY), DISP switch OFF
4 to 6 V
Power switch on (READY), DISP switch ON
Below 1 V
E1-16 (LCL+) - Body ground
SB - Body ground
Multi-information display signal
Power switch off
Below 1 V
Power switch on (READY)
Pulse generation
(Signal Waveform)
E1-17 (LCL-) - Body ground
G - Body ground
Multi-information display signal
Power switch off
Below 1 V
Power switch on (READY)
11 to 14 V
E1-18 (E3) - Body ground
W-B - Body ground
Ground (Navigation receiver assembly detection terminal)
Power switch on (READY) and the vehicle has a navigation receiver assembly
Below 1 V
Power switch on (READY) and the vehicle does not have a navigation receiver assembly
11 to 14 V
E1-19 (FE) - Body ground
W-B - Body ground
Ground (Fuel ground)
Always
Below 1 V
E1-20 (ES) - Body ground
R - Body ground
Ground (Signal ground)
Always
Below 1 V
E1-21 (B) - Body ground
SB - Body ground
Battery
Always
11 to 14 V
E1-22 (B2) - Body ground
BR - Body ground
Battery
Always
11 to 14 V
E1-23 (TC) - Body ground
R - Body ground
Light control rheostat signal (Tail cancel switch)
Power switch on (READY), turn the light control rheostat knob fully downwards
4 to 6 V
Power switch on (READY), turn the light control rheostat knob fully upwards
Below 1 V
E1-24 (SW2) - Body ground
BR - Body ground
Light control rheostat signal
Power switch on (READY), rheostat knob position is on MIN.
Below 1 V
Power switch on (READY), rheostat knob position is on MAX.
4 to 6 V
E1-25 (CANH) - Body ground
B - Body ground
CAN communication line
-
-
E1-26 (CANL) - Body ground
W - Body ground
CAN communication line
-
-
E1-27 (PMTI) - Body ground
GR - Body ground
Power meter signal
Power switch on (READY)
Pulse generation
(See waveform 2)
E1-29 (SI) - Body ground
BR - Body ground
Speed signal for other system (Input)
Power switch on (READY), turn a drive wheel slowly.
Pulse generation
(See waveform 1)
E1-30 (ILL-) - Body ground
R - Body ground
Illumination signal
Power switch on (READY), light control switch is in the HEAD/TAIL position.
11 to 14 V
E1-31 (PBLT) - Body ground
BR - Body ground
Passenger seat belt warning light signal
Sit on the passenger seat, power switch on (READY), passenger seat belt warning light OFF
11 to 14 V
Sit on the passenger seat, power switch on (READY), front passenger side seat belt warning light is blinking.
Pulse generation
(Signal waveform)
E1-34 (FR) - Body ground
GR - Body ground
Fuel signal
Power switch on (READY), fuel level is FULL.
Below 2 V
Power switch on (READY), fuel level is EMPTY.
4 to 7 V
E1-36 (MCLK) - Body ground
R - Body ground
Multi-information display signal
Power switch on (READY)
Pulse generation
E1-37 (MDAT) - Body ground
Y - Body ground
Multi-information display signal
Power switch on (READY)
Pulse generation
E1-38 (SYNC) - Body ground
L - Body ground
Multi-information display signal
Power switch on (READY)
Pulse generation
E1-39 (SW3) - Body ground
P - Body ground
Ground (Light control rheostat ground)
Always
Below 1 V
E1-40 (E2) - Body ground
W - Body ground
Ground (Power ground)
Always
Below 1 V


    I043789E03
  1. Waveform 1 (Reference): Using an oscilloscope:
    Item
    Condition
    Tool setting
    5 V/DIV., 20 ms./DIV.
    Vehicle condition
    Driving at approx.20 km/h (12 mph)

    HINT:
    When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



  2. E111225E01
  3. Waveform 2 (Reference): Using an oscilloscope:
    Item
    Condition
    Tool setting
    1 V/DIV., 20 μsec/DIV.,
    Vehicle condition
    Turn the engine switch on (Ready)


COMBINATION METER INNER CIRCUIT


  1. Combination Meter Inner Circuit


    E156034E01


    E156035E01


    E156036E02


    Terminal No. (Symbol)
    Wire Harness Side
    E1
    1 (IG+)
    GAUGE No. 2 Fuse
    2 (B)
    Turn Signal Flasher
    3 (B)
    Turn Signal Flasher
    4 (SW1)
    Light Control Rheostat
    5
    -
    6
    -
    7
    -
    8 (WLVL)
    Washer Level Warning Switch
    9 (+S)
    Each part that uses speed signal
    10 (CHK)
    Hybrid Vehicle Control ECU
    11
    -
    12 (FUW1)
    Fuel Lid Opener Switch
    13 (FUC1)
    Fuel Lid Courtesy Switch
    14 (MSSL)
    Steering Pad Switch
    15
    -
    16 (LCL+)
    Clock Assembly
    17 (LCL-)
    Clock Assembly
    18 (E3)
    Ground
    19 (FE)
    Fuel Sender Gauge Assembly
    20 (ES)
    Ground
    21 (B)
    ECU-B Fuse
    22 (B2)
    DOME Fuse
    23 (TC)
    Light Control Rheostat
    24 (SW2)
    Light Control Rheostat
    25 (CANH)
    CAN Communication Line
    26 (CANL)
    CAN Communication Line
    27 (PMTI)
    Hybrid Vehicle Control ECU
    28
    -
    29 (SI)
    Skid Control ECU
    30 (ILL-)
    Each part that uses the illumination signal
    31 (PBLT)
    Integration Control and Panel Assembly
    32
    -
    33
    -
    34 (FR)
    Fuel Sender Gauge Assembly
    35
    -
    36 (MCLK)
    Clock Assembly
    37 (MDAT)
    Clock Assembly
    38 (SYNC)
    Clock Assembly
    39 (SW3)
    Light Control Rheostat
    40 (E2)
    Ground