Home › HYBRID SYSTEM ยท P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

HYBRID CONTROL SYSTEM > SYSTEM DESCRIPTION

for Preparation Click here



BASIC OPERATION
  1. This system generates a motive force by combining the engine, MG1, MG2, and MGR in accordance with the driving conditions. Representative examples of the various combinations are described below.



  2. Front Wheel Operation:



      A111621E02
    1. Supply of electrical power from the HV battery to MG2 provides force to drive the front wheels.



    2. A111622E02
    3. While the front wheels are being driven by the engine via the compound gear unit, MG1 is also being driven by the engine via the compound gear unit, in order to supply the electricity that MG1 generates to MG2.



    4. A111623E02
    5. MG1 is also driven by the engine via the compound gear unit, in order to charge the HV battery.



    6. A111624E02
    7. When the vehicle is decelerating, kinetic energy from the front wheels is recovered and converted into electrical energy by means of MG2, and used to recharge the HV battery by.



  3. Rear Wheels



      A111625E02
    1. To ensure the proper driving force of the vehicle during start-off or acceleration, the electrical power of the HV battery is supplied to MGR in order to drive the rear wheels.



    2. A111626E02
    3. During the full throttle acceleration of the vehicle, both the electrical power of the HV battery and the electrical power generated by MG1 are supplied to MGR in order to drive the rear wheels.



    4. A111627E02
    5. When the vehicle is decelerating, kinetic energy from the rear wheels is recovered and converted into electrical energy by means of MGR, and used to recharge the HV battery.


SYSTEM DIAGRAM

A183395E01


FUNCTION OF MAIN COMPONENTS

Item
Outline
Hybrid Transaxle
MG1
  1. MG1, which is driven by the engine, generates high-voltage electricity in order to operate MG2 or charge the HV battery. Also, it functions as a starter to start the engine.
  2. MG1 operates so that the gear ratio of the power split planetary gear unit will optimally suit the driving conditions of the vehicle.
MG2
  1. Driven by electrical power from MG1 or the HV battery, and generates motive force for the front wheels.
  2. During braking, or when the accelerator pedal is not depressed, it generates electricity to recharge the HV battery (Regenerative braking control).
Compound Gear Unit
Power Split Planetary Gear
Distributes the engine drive force as appropriate to directly drive the vehicle as well as drive MG1.
Motor Speed Reduction Planetary Gear
Located between MG2 and the power split planetary gear, the motor speed reduction planetary gear reduces the rotational speed of MG2 in accordance with the characteristics of a planetary gearset, in order to increase torque.
Rear Transaxle
MGR
  1. Driven by electrical power from MG1 or the HV battery, and generates motive force for the rear wheels.
  2. During braking, or when the accelerator pedal is not depressed, it generates electricity to recharge the HV battery (Regenerative braking control).
HV Battery
  1. Supplies electrical power to MG1, MG2, and MGR in accordance with the driving conditions of the vehicle.
  2. Recharged by the MG1, MG2, and MGR in accordance with the SOC and the driving conditions of the vehicle.
Inverter with Converter Assembly
Converts the high-voltage DC (HV battery) into AC (MG1 and MG2) and vice versa (converts AC into DC).

Boost Converter
Boosts the voltage of the HV battery from DC 288 V to DC 650 V (maximum) and vice versa (drops DC 650 V to DC 288 V).
DC/DC Converter
Converts a voltage of DC 288 V to DC 12 V in order to supply electricity to body electrical components, as well as to recharge the auxiliary battery (DC 12 V).
MG ECU
  1. Controls the inverter and boost converter in accordance with the signals received from the hybrid vehicle control ECU, thus driving MG1, MG2, or MGR or causing them to generate electricity.
  2. Controls the DC/DC converter in accordance with the signals received from the hybrid vehicle control ECU.
Hybrid Vehicle Control ECU
Performs comprehensive control of the THS-II system.
  1. Information from each sensor as well as from the ECU (battery smart unit, skid control ECU, and EPS ECU) is received, and based on this information, the required torque and output power is calculated. The hybrid vehicle control ECU sends the calculated result to the inverter with converter assembly and skid control ECU.
  2. Activates the ETCS-i (Electronic Throttle Control System-intelligent) in accordance with the target engine speed and required engine motive force.
  3. Monitors the charging condition of the HV battery.
  4. Controls the cooling fan of the HV battery.
Battery Smart Unit
  1. Monitors the conditions of the HV battery and transmits this information to the hybrid vehicle control ECU.
  2. Monitors the fault current of the HV battery.
Skid Control ECU
  1. During braking, the skid control ECU calculates the regenerative braking force that is required for control and transmits it to the hybrid vehicle control ECU.
  2. Calculates the motive force that is required for control during the operation of TRAC or VSC and transmits it to the hybrid vehicle control ECU.
  3. Transmits a front and rear wheel torque distribution request to the hybrid vehicle control ECU for the purpose of 4WD system control.
Accelerator Pedal Position Sensor
Converts the accelerator pedal position into electrical signals and outputs them to the hybrid vehicle control ECU.
Shift Lever Position Sensor
Converts the shift position into electrical signals and outputs them to the hybrid vehicle control ECU.
HV Relay Assembly
Connects and disconnects the high-voltage power circuit between the battery and the inverter with converter assembly, through the use of signals from the hybrid vehicle control ECU.
Interlock Switch
(for Inverter Cover and Service Plug Grip)
Verifies that the cover of both the inverter and the service plug grip have been installed.
Circuit Breaker Sensor
Detects the impact that is applied to the vehicle during a collision and transmits a signal to the hybrid vehicle control ECU. Upon receiving this signal, the hybrid vehicle control ECU operates the HV relay assembly to shut down the power supply.
Service Plug Grip
Shuts off the high-voltage circuit of the HV battery when this service plug grip is removed for vehicle inspection or maintenance.