Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > VC Output Circuit

for Preparation Click here


DESCRIPTION

The ECM constantly generates 5 V power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM (included in the hybrid vehicle control ECU) also provides this power to the sensors through the VC output circuit.

A116143E60

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are deactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the power switch is first turned on (IG). The MIL goes off when the hybrid system is started.


WIRING DIAGRAM


A153158E06


INSPECTION PROCEDURE

1.CHECK MIL CONDITION
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the power switch on (IG).

    OK:
    MIL lights up.



NG
Go to step 2
OK

SYSTEM OK 

2.CHECK COMMUNICATION BETWEEN TECHSTREAM AND HYBRID VEHICLE CONTROL ECU
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Check for communication between the Techstream and hybrid vehicle control ECU.

    Result:

    Result
    Proceed to
    Communication is possible
    A
    Communication is not possible
    B



A
GO TO MIL CIRCUIT
B


3.CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the throttle body connector.

  1. Turn the power switch on (IG).

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the throttle body connector.



A
REPLACE THROTTLE BODY ASSEMBLY (Click here)
B


4.CHECK MIL (VAPOR PRESSURE SENSOR)
  1. Disconnect the fuel tank pressure sensor connector.

  1. Turn the power switch on (IG).

  1. Check the MIL.

    Result:

    Condition
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE VAPOR PRESSURE SENSOR ASSEMBLY (Click here)
B


5.CHECK MIL (CANISTER PUMP MODULE)


    A153160
  1. Disconnect the canister pump module connector.

  1. Turn the power switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the canister pump module connector.



A
REPLACE CHARCOAL CANISTER ASSEMBLY (Click here)
B


6.CHECK HARNESS AND CONNECTOR


    A153161E06
  1. Disconnect the throttle body connector.

  1. Disconnect the fuel tank pressure sensor connector.

  1. Disconnect the canister pump module connector.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B1-18 (VC) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the throttle body connector.

  1. Reconnect the fuel tank pressure sensor connector.

  1. Reconnect the canister pump module connector.

  1. Reconnect the hybrid vehicle control ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)