Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > TERMINALS OF ECU

for Preparation Click here



CHECK AIR CONDITIONING AMPLIFIER

E127561E03

  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    Check from the rear of the connector while it is connected to the air conditioning amplifier.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D37-1 (IG+) - D37-14 (GND)
    GR - W-B
    Power source (IG)
    Power switch on (IG)
    11 to 14 V
    D37-5 (TAM) - D37-14 (GND)
    B - W-B
    Ambient temperature sensor signal
    Power switch on (IG)
    1.8 to 2.2 V
    Ambient temperature: 25°C (77°F)
    D37-9 (PRE) - D37-13 (SG-2)
    R - L
    Air conditioning pressure sensor signal
    Refrigerant pressure: Normal
    0.76 to 4.74 V
    D37-9 (PRE) - D37-13 (SG-2)
    R - L
    Air conditioning pressure sensor signal
    Refrigerant pressure: Abnormal (less than 0.196 MPa [2.0 kgf/cm2, 28 psi])
    0.5 to 4.83 V
    D37-9 (PRE) - D37-13 (SG-2)
    R - L
    Air conditioning pressure sensor signal
    Refrigerant pressure: Abnormal (more than 3.03 MPa [32 kgf/cm2, 440 psi])
    4.74 V or higher
    D37-10 (S5-3) - D37-14 (GND)
    L - W-B
    Power supply for pressure sensor
    Power switch on (IG)
    4.5 to 5.5 V
    D37-11 (CANH) - D37-14 (GND)
    B - W-B
    Hi-level CAN bus line
    Power switch on (IG)
    Pulse generation
    (see waveform 2)
    D37-12 (CANL) - D37-14 (GND)
    W - W-B
    Lo-level CAN bus line
    Power switch on (IG)
    Pulse generation
    (see waveform 3)
    D37-13 (SG-2) - Body ground
    L - Body ground
    Ground for pressure sensor
    Always
    Below 1 V
    D37-14 (GND) - Body ground
    W-B - Body ground
    Ground for main power supply
    Always
    Below 1 V
    D37-21 (B) - D37-14 (GND)
    LG - W-B
    Power source (Back-up)
    Always
    11 to 14 V
    D37-23 (BLW) - D37-14 (GND)
    R - W-B
    Blower motor control signal
    Power switch on (IG)
    Pulse generation
    (see waveform 1)
    Blower switch LO
    D37-29 (TR) - D37-35 (SG-4)
    BR- LG
    Room temperature sensor signal (for Front)
    Power switch on (IG)
    1.8 to 2.2 V
    Vehicle interior temperature: 25°C (77°F)
    D37-32 (TSP) - D37-14 (GND)
    Y - W-B
    Front passenger side solar sensor signal
    Power switch on (IG)
    0.8 to 4.3 V
    Solar sensor subject to electric light
    D37-33 (TSD) - D37-14 (GND)
    O - W-B
    Driver side solar sensor signal
    Power switch on (IG)
    0.8 to 4.3 V
    Solar sensor subject to electric light
    D37-35 (SG-4) - Body ground
    LG - Body ground
    Ground for room temperature sensor (for Front)
    Always
    Below 1 V
    D37-37 (LIN1) - D37-14 (GND)
    R - W-B
    LIN communication signal
    Power switch on (IG)
    Pulse generation
    D37-38 (RDFG) - D37-14 (GND)
    W - W-B
    Rear defogger switch signal
    Power switch on (IG)
    Rear defogger switch OFF
    11 to 14 V
    D37-38 (RDFG) - D37-14 (GND)
    W - W-B
    Rear defogger switch signal
    Power switch on (IG)
    Rear defogger switch ON
    Below 1 V
    D38-1 (RBUS) - D38-21 (RBUG) (*)
    R - V
    BUS IC control signal (for Rear)
    Power switch on (IG)
    Pulse generation
    D38-4 (TEC) - D38-19 (SGND) (*)
    B - GR
    Evaporator temperature sensor signal (for Rear)
    Power switch on (IG)
    1.4 to 1.8 V
    Evaporator temperature: 15°C (59°F)
    D38-7 (SG-6) - Body ground (*1)
    W - Body ground
    Ground for room temperature sensor signal (for Rear)
    Always
    Below 1 V
    D38-13 (RLIN) - D38-20 (GND2) (*)
    B - SB
    LIN communication signal (for Rear)
    Power switch on (IG)
    Pulse generation
    D38-17 (TR) - D38-7 (SG-6) (*1)
    BR - W
    Room temperature sensor signal (for Rear)
    Power switch on (IG)
    1.8 to 2.2 V
    Vehicle interior temperature: 25°C (77°F)
    D38-19 (SGND) - Body ground (*)
    GR - Body ground
    Ground for evaporator temperature sensor signal (for Rear)
    Always
    Below 1 V
    D38-20 (GND2) - Body ground (*)
    SB - Body ground
    Ground for power supply
    Always
    Below 1 V
    D38-21 (RBUG) - Body ground (*)
    V - Body ground
    Ground for BUS IC (for Rear)
    Always
    Below 1 V
    D38-22 (BLWH) - D38-20 (GND2) (*)
    G - SB
    Blower motor control signal (for Rear)
    Power switch on (IG)
    Pulse generation
    Blower switch LO
    D38-23 (RBBU) - D38-21 (RBUG) (*)
    Y - V
    Power supply for BUS IC (for Rear)
    Power switch on (IG)
    11 to 14 V
    D38-24 (+B2) - D38-20 (GND2) (*)
    LG - SB
    Power source (Back-up) (for Rear)
    Always
    11 to 14 V
    z17-2 (BUS G) - Body ground
    -
    Ground for BUS IC
    Always
    Below 1 V
    z17-3 (BUS) - z17-2 (BUS G)
    -
    BUS IC control signal
    Power switch on (IG)
    Pulse generation
    z17-4 (B BUS) - z17-2 (BUS G)
    -
    Power supply for BUS IC
    Power switch on (IG)
    11 to 14 V
    z17-5 (SGA) - Body ground
    -
    Ground for evaporator temperature sensor
    Always
    Below 1 V
    z17-6 (TEA) - z17-5 (SGA)
    -
    Evaporator temperature sensor signal (for Front)
    Power switch on (IG)
    1.4 to 1.8 V
    Evaporator temperature: 15°C (59°F)



  2. E103396E05
  3. Using an oscilloscope, check waveform 1.
    Blower motor control signal 
    Item
    Content
    Tester Connection
    D37-23 (BLW) - D37-14 (GND)
    Tool Setting
    1 V/DIV., 500 μsec./DIV.
    Condition
    Power switch on (IG), Blower switch LO

    HINT:
    When the blower level is increased, the duty ratio changes accordingly.



  4. A086154E36
  5. Using an oscilloscope, check waveform 2.
    CAN communication signal 
    Item
    Content
    Tester Connection
    D37-11 (CANH) - D37-14 (GND)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Power switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.



  6. A086155E34
  7. Using an oscilloscope, check waveform 3.
    CAN communication signal 
    Item
    Content
    Tester Connection
    D37-12 (CANL) - D37-14 (GND)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Power switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.
    *: w/ Rear Air Conditioning
    *1: for Rear Automatic Air Conditioning


HYBRID VEHICLE CONTROL ECU

E109306E04

HINT:
Check from the rear of the connector while it is connected to the hybrid vehicle control ECU.


Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
B2-14 (CLK) - Body ground
G - Body ground
Compressor operation signal
Power switch on (IG)
Pulse generation
(see waveform 1)
B2-15 (ITE) - Body ground
P - Body ground
Compressor operation signal
Power switch on (IG)
Pulse generation
(see waveform 2)
B2-16 (ETI) - Body ground
Y - Body ground
Compressor operation signal
Power switch on (IG)
Pulse generation
(see waveform 3)
B2-18 (STB) - Body ground
B - Body ground
Compressor operation signal
Power switch on (IG)
11 to 14 V
B2-18 (STB) - Body ground
B - Body ground
Compressor operation signal
Power switch on (IG)
Below 1 V
A43-4 (WP) - Body ground
V - Body ground
Water pump power switch: ON operation signal
Heater water pump not operated
11 to 14 V
A43-4 (WP) - Body ground
V - Body ground
Water pump operation signal
Heater water pump operated
Below 1 V


    E110722E04
  1. Using an oscilloscope, check waveform 1.

    1. Measure the waveform between terminal CLK (B2-14) of the hybrid vehicle control ECU and body ground.

      OK:
      Waveform appears as shown in the illustration.

      HINT:
      Waveform cycle varies with the communication contents.



  2. E110723E02
  3. Using an oscilloscope, check waveform 2.

    1. Measure the waveform between terminal ITE (B2-15) of the hybrid vehicle control ECU and body ground.

      OK:
      Waveform appears as shown in the illustration.

      HINT:
      Waveform cycle varies with the communication contents.



  4. E110724E05
  5. Using an oscilloscope, check waveform 3.

    1. Measure the waveform between terminal CLK (B2-16) of the hybrid vehicle control ECU and body ground.

      OK:
      Waveform appears as shown in the illustration.

      HINT:
      Waveform cycle varies with the communication contents.


CHECK FRONT AIR CONDITIONING CONTROL

E152670E01

  1. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E10-2 (IG+) - E10-10 (GND)
    V - GR
    Power source (IG)
    Power switch on (IG)
    11 to 14 V
    E10-5 (LIN1) - E10-10 (GND)
    R - GR
    LIN communication signal
    Power switch on (IG)
    Pulse generation
    E10-10 (GND) - Body ground
    GR - Body ground
    Ground for front air conditioning control
    Always
    Below 1 V


CHECK REAR AIR CONDITIONING CONTROL (for Rear Air Conditioning)

E152670E02

  1. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    R1-2 (IG+) - R1-10 (E)
    V - W-B
    Power source (IG)
    Power switch on (IG)
    11 to 14 V
    R1-5 (MPX-) - R1-10 (E)
    B - W-B
    LIN communication signal
    Power switch on (IG)
    Pulse generation
    R1-10 (E) - Body ground
    W-B - Body ground
    Ground for rear air conditioning control
    Always
    Below 1 V