Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)

AIR CONDITIONING SYSTEM (for Manual Air Conditioning System) > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators, and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the Techstream to the DLC3.

  2. Turn the power switch on (IG) and turn the Techstream on.

  3. Read the Data List by following the prompts on the Techstream.

    Data List / Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Ambient Temp Sensor
    Ambient temperature sensor /
    Min.: -23.3°C (-9.94°F)
    Max.: 65.95°C (150.71°F)
    Actual ambient temperature is displayed
    Open in circuit: -23.3°C (-9.94°F)
    Short in circuit: 65.95°C (150.71°F)
    Adjusted Ambient Temp
    Adjusted ambient
    Min.: -30.8°C (-23.44°F)
    Max.: 50.8°C (123.44°F)
    Adjusted ambient temperature is displayed
    -
    Evaporator Fin Temperature
    Evaporator temperature sensor /
    Min.: -29.7°C (-21.46°F)
    Max.: 59.55°C (139.19°F)
    Actual evaporator temperature is displayed
    Open in circuit: -29.7°C (- 21.46°F)
    Short in circuit: 59.55°C (139.19°F)
    Engine Coolant Temp
    Engine coolant temperature sensor /
    Min.: 1.3°C (34.34°F)
    Max.: 90.55°C (194.99°F)
    Actual engine coolant temperature is displayed
    -
    Regulator Pressure Sensor
    Regulator pressure sensor /
    Min.: 0 kgf/cm2G
    Max.: 38.25 kgf/cm2G
    Actual regulator pressure is displayed
    -
    Ambient Temp Sensor(Rear)
    Rear evaporator temperature sensor /
    Min.: -29.7°C (-21.46°F)
    Max.: 59.55°C (139.19°F)
    Actual rear evaporator temperature is displayed
    Open in circuit: -29.7°C (- 21.46°F)
    Short in circuit: 59.55°C (139.19°F)
    Blower Motor Level(Rear)
    Rear blower motor speed level /
    Min.; 0, Max.: 31
    Displayed speed level increases in range between 0 and 31 as rear blower motor speed increases
    -
    Air Mix Sensor Targ Pulse(P)
    Passenger side air mix servo motor target pulse /
    Min.: 0, Max.: 255
    MAX. COLD: 105 (pulse)
    MAX. HOT: 7 (pulse)
    -
    Air Outlet Servo Pulse(D)
    Driver side air outlet servo motor target /
    Min.: 0, Max.: 255
    FACE: 8 (pulse)
    B/L: 30 (pulse)
    FOOT: 67 (pulse)
    FOOT/DEF: 80 (pulse)
    DEF: 97 (pulse)
    -
    Air Inlet Damper Targ Pulse
    Air inlet damper target pulse /
    Min.: 0, Max.: 255
    RECIRCULATION: 7 (pulse)
    FRESH: 28 (pulse)
    -
    Compressor Speed
    Compressor speed / Min.: 0, Max.: 65535 rpm
    Displays actual rotation speed in the range between 0 rpm and 8600 rpm
    -
    Compressor Target Speed
    Compressor speed / Min.: 0, Max.: 65535 rpm
    Displays actual rotation speed in the range between 0 rpm and 8600 rpm
    -
    Air Outlet Servo Pulse(R)
    Rear side air outlet control servo motor target pulse /
    Min.: 0, Max.: 255
    Rr FACE: 83 (pulse)
    Rr B/L: 38 (pulse)
    Rr FOOT: 7 (pulse)
    -
    Air Mix Servo Targ Pulse(R)
    Rear side air mix control servo motor target pulse /
    Min.: 0, Max.: 255
    MAX. COLD: 9 (pulse)
    MAX. HOT: 54 (pulse)
    -
    #Codes
    Number of trouble codes /
    Min.: 0, Max.: 255
    Number of DTCs is displayed
    -


PERFORM ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the power switch on (IG) and turn Techstream on.

  3. Perform the Active Test by following the prompts on the Techstream.

    Active Test / Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Compressor Target Speed
    Compressor target speed
    Min.: 0, Max.: 7500
    -
    Defogger relay (Rear)
    Defogger relay (Rear)
    OFF, ON
    -
    Electrical Fan
    Electrical fan
    OFF, ON
    -
    Water Pump
    Water pump relay
    OFF, ON
    -
    Air Mix Servo Targ pulse (P)
    Air mix servo motor pulse (P side)
    Min.: 7, Max.: 105
    -
    Air Outlet Servo Targ pulse (D)
    Air outlet servo motor pulse (D side)
    Min.: 8, Max.: 97
    -
    Air Inlet Dmaper Targ pulse (D)
    Air inlet damper target pulse
    Min.: 7, Max.: 28
    -
    Rear Air Mix Servo Targ pulse
    Rear air mix control servo motor pulse
    Min.: 9, Max.: 54
    -
    A/O Servo pulse (Rr D)
    Air outlet servo motor pulse (Rr D side)
    Min.: 7, Max.: 83
    -