Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › FRONT COOLING UNIT

FRONT COOLING UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL NO. 1 COOLER THERMISTOR


    E151029E01
  1. Install the No. 1 cooler thermistor as shown in the illustration.
    Part
    Length
    A
    34.3 mm
    1.35 in.
    B
    20.9 mm
    0.82 in.
    C
    50 mm
    1.96 in.

    NOTICE:
    1. Be sure to insert the thermistor only once because reinserting it into the same position will not allow it to be firmly secured.
    2. When reusing the evaporator, insert the thermistor one row next to the one that has been used previously (X in the illustration).
    3. After inserting the thermistor, do not apply excessive force to the wire.
    4. Directly insert the thermistor until the edge of plastic case "a" comes into contact with evaporator "b".



2. INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY


    E151027
  1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces.

    Compressor oil:
    ND-OIL 11 or equivalent

    NOTICE:
    1. Keep the O-rings and O-ring fitting surfaces clean from dirt or any foreign objects.
    2. Do not use any compressor oil other than ND-OIL 11 or equivalent. If any compressor oil other than ND-OIL 11 or equivalent is used, compressor motor insulation performance may decrease, resulting in a leakage of electric power.

  1. Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.



    E151026
  1. Install the No. 1 cooler evaporator sub-assembly.

  1. Engage the clamp.



    E151025
  1. Engage the 5 claws.

  1. Install the plate cover with the 6 screws.

  1. Connect the connector.



3. INSTALL COOLER EXPANSION VALVE


    E151024
  1. Using a 4 mm hexagon wrench, install the cooler expansion valve with the 2 hexagon bolts.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }



4. INSTALL ASPIRATOR


    E151023
  1. Engage the 2 claws.

  1. Engage the clamp and install the aspirator.



5. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY


    E151021
  1. Install the heater radiator unit sub-assembly as shown in the illustration.



6. INSTALL HEATER CLAMP


    E151019
  1. Install the clamp with the screw.

  1. Engage the 3 claws and install the heater clamp.



7. INSTALL FRONT AIR MIX CONTROL SERVO MOTOR SUB-ASSEMBLY


    E151018E01
  1. Using the reference point, install the front air mix control servo motor sub-assembly with the 2 screws.

  1. Connect the connector.



8. INSTALL FRONT AIR OUTLET CONTROL SERVO MOTOR SUB-ASSEMBLY


    E151058E01
  1. Install the front air outlet control servo motor sub-assembly with the 3 screws.

  1. Connect the 2 connectors.



9. INSTALL BLOWER ASSEMBLY


    E151015
  1. Engage the 2 claws.

  1. Install the blower assembly with the 2 screws.

  1. Connect the connector.



10. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY


    E151013
  1. Engage the 3 claws and install the No. 3 air duct sub-assembly as shown in the illustration.



11. INSTALL ID CODE BOX (IMMOBILISER CODE ECU)


    B170918
  1. Engage the 3 claws and install the ID code box (immobiliser code ECU) as shown in the illustration.