FRONT DRIVE SHAFT > REASSEMBLY |
| 1. INSTALL SIDE GEAR SHAFT HOLDER BEARING (for RH Side) |
Install a new bearing bracket hole snap ring to the front drive shaft assembly RH.
![]() |
Using SST, install a new front drive shaft bearing.
![]() |
Using a snap ring expander, install a new drive shaft hole snap ring.
| 2. INSTALL FRONT DRIVE SHAFT DUST COVER (for RH Side) |
![]() |
Using SST and a press, install a new drive shaft dust cover.
| 3. INSTALL FRONT DRIVE SHAFT DUST COVER RH (for RH Side) |
![]() |
Using SST and a press, install a new drive shaft dust cover RH until distance (A) from the tip of the center drive shaft to the drive shaft dust cover RH meets the specification.
| 4. INSTALL FRONT DRIVE SHAFT DUST COVER LH (for LH Side) |
![]() |
Using SST and a press, install a new drive shaft dust cover LH.
| 5. INSTALL FRONT AXLE OUTBOARD JOINT BOOT |
![]() |
Install new parts to the outboard joint shaft in the following order:
No. 2 front axle outboard joint boot clamp
Front axle outboard joint boot
Front axle outboard joint boot clamp
Pack the front drive outboard joint shaft and front axle outboard joint boot with grease.
| 6. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP |
Hold the drive shaft lightly in a vise between aluminum plates.
Install the front axle outboard joint boot clamp onto the front axle outboard joint boot.
![]() |
Place SST onto the front axle outboard joint boot clamp.
Tighten SST so that the front axle outboard joint boot clamp is pinched.
![]() |
Using SST, measure the clearance of the front axle outboard joint boot clamp.
| 7. INSTALL NO. 2 FRONT AXLE OUTBOARD JOINT BOOT CLAMP |
Install the No. 2 front axle outboard joint boot clamp onto the front axle outboard joint boot.
![]() |
Place SST onto the No. 2 front axle outboard joint boot clamp.
Tighten SST so that the No. 2 front axle outboard joint boot clamp is pinched.
![]() |
Using SST, measure the clearance of the No. 2 front axle outboard joint boot clamp.
| 8. INSTALL FRONT DRIVE SHAFT DAMPER |
![]() |
Install the drive shaft damper to the drive shaft.
Make sure that the damper is on the shaft groove.
Set the distance as specified below.
Install the drive shaft damper clamp onto the drive shaft damper.
![]() |
Place SST onto the drive shaft damper clamp.
Tighten SST so that the clamp is pinched.
![]() |
Using SST, measure the clearance of the drive shaft damper clamp.
| 9. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY |
Wrap the splines of the outboard joint shaft with vinyl tape to prevent the boot from being damaged.
![]() |
Install new parts to the front drive outboard joint shaft assembly in the following order:
Front axle inboard joint boot clamp
Front axle inboard joint boot
No. 2 front axle inboard joint boot clamp
Place the beveled side of the tripod joint axial spline toward the front drive outboard joint shaft assembly.
Align the matchmarks placed before removal.
Using a brass bar and hammer, tap in the tripod joint to the front drive outboard joint shaft assembly.
![]() |
Using a snap ring expander, install a new shaft snap ring.
Pack the front drive inboard joint assembly and front axle inboard boot with grease.
![]() |
Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.
| 10. INSTALL FRONT AXLE INBOARD JOINT BOOT |
Install the front axle inboard joint boot to the front drive inboard joint assembly.
![]() |
Check whether the drive shaft dimensions are within the following specifications.
| LH | 591.8 to 596.4 mm (23.30 to 23.48 in.) |
| RH | 933.06 to 937.66 mm (36.74 to 36.91 in.) |
| 11. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP |
Hold the drive shaft lightly in a vise between aluminum plates.
Secure the inboard joint boot clamp onto the boot.
![]() |
Place SST onto the inboard joint boot clamp.
Tighten SST so that the front axle inboard joint boot clamp is pinched.
![]() |
Using SST, measure the clearance of the front axle inboard joint boot clamp.
| 12. INSTALL NO. 2 FRONT AXLE INBOARD JOINT BOOT CLAMP |
Hold the inboard joint shaft assembly in a vise between aluminium plates.
Secure the No. 2 front axle inboard joint boot clamp onto the boot.
![]() |
Place SST onto the No. 2 front axle inboard joint boot clamp.
Tighten SST so that the No. 2 front axle inboard joint boot clamp is pinched.
![]() |
Using SST, measure the clearance of the No. 2 front axle inboard joint boot clamp.
| 13. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING |
Install a new front drive shaft hole snap ring.
| 14. INSPECT FRONT DRIVE SHAFT ASSEMBLY LH |
![]() |
Check that there is no excessive play in the outboard joint.
Check that the inboard joint slides smoothly in the thrust direction.
Check that there is no excessive play in the radial direction of the inboard joint.
Check the boots for damage.