Home › ENGINE › 3MZ-FE STARTING › SMART KEY SYSTEM

DTC    B2274    ACC Monitor Malfunction

for Preparation Click here


DESCRIPTION

This DTC is output when there is a problem in the ACCD output circuit, which is from the inside of the main body ECU (instrument panel junction block) to the ACC relay.

HINT:
When the main body ECU (instrument panel junction block) is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
After the main body ECU (instrument panel junction block) is replaced, perform the registration procedures for the engine immobiliser system (Click here).


DTC No.
DTC Detection Condition
Trouble Area
B2274
ACC relay actuation circuit inside main body ECU (instrument panel junction block) or other related circuit is malfunctioning
  1. Main body ECU (instrument panel junction block)
  2. ACC relay
  3. Wire harness or connector

WIRING DIAGRAM


B176780E02


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream main switch on.

  1. Read the Data List according to the displays on the tester.

    HINT:
    When using Techstream with the power switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.


    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ACC Relay Monitor
    Status of ACC Relay Monitor / ON or OFF
    ON: Power switch on (ACC)
    OFF: Power switch off
    -

    OK:
    "ON" (power switch on (ACC)) appears on the screen.



NG
Go to step 3
OK


2.CHECK DTC OUTPUT
  1. Delete the DTCs (Click here).

    HINT:
    After all DTCs cleared, turn the power switch on (IG) and depress the brake pedal. After 10 seconds have elapsed, check if the trouble occurs again.

  1. Check for DTCs again.

OK:
No DTC is output.



NG
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
OK

USE SYMPTOM METHOD TO CHECK (Click here)  

3.INSPECT RELAY (ACC RELAY)


    A169410
  1. Remove the ACC relay from the instrument panel junction block

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE ACC RELAY
OK


4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK)


  1. Disconnect the D8 connector from the main body ECU (instrument panel junction block).


    B138001E30

  1. Disconnect the 1I connector from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1I-3 - D8-22 (ACCD)
    Always
    Below 1 Ω
    D8-22 (ACCD) or 1I-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK)
OK


5.CHECK HARNESS AND CONNECTOR


    B176773E01
  1. Disconnect the 1A and 1F connectors from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1F-10 - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    1A-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)