Home › BODY ELECTRICAL › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM

WIRELESS DOOR LOCK CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


  1. Disconnect the main body ECU (instrument panel junction block assembly) connectors.


    B139428E12

  2. Measure the resistance and voltage between each terminal of the wire harness side connectors and body ground.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    1A-1 (IG) - Body ground
    B - Body ground
    IG power supply (IG signal)
    power switch on (IG) → off
    10 to 14 V → Below 1 V
    1A-1 (ACC) - Body ground
    B - Body ground
    ACC power supply (ACC signal)
    power switch on (ACC) → off
    10 to 14 V → Below 1 V
    1D-16 (ALTB) - Body ground
    W - Body ground
    +B (power system alternator system) power supply
    Always
    10 to 14 V
    D8-24 (DCTY) - Body ground
    G - Body ground
    Driver side door courtesy light switch input
    Driver side door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    D7-21 (PCTY) - Body ground
    SB - Body ground
    Passenger side courtesy light switch input
    Passenger side door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    D7-7 (RCTY) - Body ground
    GR - Body ground
    Rear courtesy light switch RH input
    Rear door RH CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    1O-7 (LCTY) - Body ground
    B - Body ground
    Rear courtesy light switch LH input
    Rear door LH CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    D7-25 (BCTY) - Body ground
    L - Body ground
    Back door courtesy light switch input
    Back door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    1F-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1M-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the main body (instrument panel J/B) connectors.

  4. Measure the voltage between each terminal of the wire harness side connectors and body ground.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D8-1 (TR+) - Body ground*3
    LG - Body ground
    Back door opener motor
    Back door CLOSED (LOCKED) → OPEN (UNLOCKED)
    Below 1 V → 10 to 14 V*1
    D9-4 (HAZ) - Body ground
    O - Body ground
    Turn signal flasher relay signal
    Any transmitter switch is pressed → not pressed
    Below 1 V → 10 to 14 V*2

    HINT:
    1. *1: When operating the motor.
    2. *2: When operating the answer back function.
    3. *3: w/o Power Back Door System


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B178888E03

  1. Disconnect the D40 certification ECU (smart key ECU assembly) connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D40-17 (E) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    D40-1 (+B) - D40-17 (E)
    B - B
    Battery power supply
    Always
    11 to 14 V
    D40-18 (IG) - D40-17 (E)
    G - B
    IG power supply
    power switch on (IG)
    11 to 14 V
    power switch off
    Below 1 V

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D40 certification ECU (smart key ECU assembly) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D40-39 (RSSI) - D40-17 (E)
    B - B
    Door control receiver output signal
    power switch off, all doors closed and transmitter switch not pressed
    11 to 14 V
    power switch off, all doors closed and transmitter switch pressed
    Below 1 V
    D40-38 (RDA) - D40-17 (E)
    Y - B
    Door control receiver output signal
    power switch off, all doors closed and transmitter switch not pressed
    4.6 to 5.4 V
    power switch off, all doors closed and transmitter switch pressed
    Pulse generation
    D40-29 (RCO) - D40-17 (E)
    V - B
    Supply battery to door control receiver
    power switch off, all doors closed and transmitter switch pressed
    4.6 to 5.4 V
    D40-21 (BZR) - Body ground
    R - Body ground
    Wireless door lock buzzer signal
    Wireless door lock buzzer OFF → ON
    Below 1 V → Pulse generation

    1. If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.