Home › STEERING › POWER STEERING › POWER STEERING SYSTEM

POWER STEERING SYSTEM > EPS Warning Light Circuit

for Preparation Click here


DESCRIPTION

If the power steering ECU detects a malfunction, the P/S warning light comes on. At this time, the power steering ECU stores a DTC in its memory.

WIRING DIAGRAM


C170028E05


INSPECTION PROCEDURE

1.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)
  1. Turn the power switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Using the Techstream, check for DTCs and confirm that there are no problems in the CAN communication system.

    OK:
    CAN DTCs are not output.



NG
GO TO CAN COMMUNICATION SYSTEM (Click here)
OK


2.READ VALUE USING TECHSTREAM (IG POWER SUPPLY)
  1. Enter the following menus: Chassis / EMPS / Data List.

  1. Select the item "IG Power Supply" in the Data List and read the value displayed on the Techstream.

    EMPS: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG Power Supply
    ECU power source voltage:
    Min.: 0 V
    Max.: 20.1531 V
    11 to 14 V
    Power switch on (IG)



NG
Go to step 4
OK


3.PERFORM ACTIVE TEST BY TECHSTREAM
  1. Enter the following menus: Body / Combination meter / Active Test.

  1. According to the display on tester, perform the "Active Test".

    Combination meter: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. EPS (*1)
    P/S Warning Light
    ON or OFF
    Confirm that the vehicle is stopped, engine idling
    Master Warning (*2)
    Master Warning Light
    ON or OFF
    Confirm that the vehicle is stopped, engine idling
    *1: w/o Multi-information Display
    *2: w/ Multi-information Display

    OK:
    Indicator comes on.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE POWER STEERING ECU (Click here)  

4.INSPECT FUSE (ECU IG NO. 1)
  1. Remove the ECU IG No. 1 fuse from the instrument panel junction block.

  1. Measure the resistance of the fuse.

    OK:
    Below 1 Ω



NG
REPLACE FUSE
OK


5.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BATTERY AND BODY GROUND)
C113533E12
  1. Disconnect the connectors from the power steering ECU.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D6-5 (IG) - Body ground
    Power switch on (IG)
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D5-2 (PGND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Enter the following menus: Body / Combination meter / Active Test.

  1. According to the display on tester, perform the "Active Test".

    Combination meter: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. EPS (*1)
    P/S Warning Light
    ON or OFF
    Confirm that the vehicle is stopped, engine idling
    Master Warning (*2)
    Master Warning Light
    ON or OFF
    Confirm that the vehicle is stopped, engine idling
    *1: w/o Multi-information Display
    *2: w/ Multi-information Display

    OK:
    Indicator comes on.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE POWER STEERING ECU (Click here)