BACK WINDOW SUPPORT > INSTALLATION |
| 1. PRECAUTION |
| 2. INSTALL BACK WINDOW STAY BOLT |
When replacing the back window stay bolt with a new one:
Clean the threaded surface on the vehicle body with a non-residue solvent.
![]() |
Install the back window stay bolt.
When reusing the back window stay bolt:
Clean the threaded surface on the vehicle body with a non-residue solvent.
Apply adhesive to the threads of the back window stay bolt.
![]() |
Install the back window stay bolt.
| 3. INSTALL BACK WINDOW STAY ASSEMBLY |
When replacing the back window stay assembly with a new one:
![]() |
Install the 2 stop rings to the back window stay assembly.
![]() |
Install the back window stay assembly.
Check that the hood support assembly is engaged in the ball joint and that the hood support assembly cannot be pulled out.
| 4. REMOVE BACK WINDOW UPPER TRIM PANEL ASSEMBLY |
![]() |
Disengage the 4 clips and 4 claws, and remove the back window upper trim panel assembly.
| 5. REMOVE BACK DOOR TRIM COVER LH (w/o Power Back Door) |
![]() |
Disengage the 2 clips and 2 claws, and remove the back door trim cover LH.
| 6. REMOVE BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door) |
![]() |
Disengage the 6 claws, and remove the back door service hole cover LH.
| 7. DISCONNECT POWER BACK DOOR ROD (w/ Power Back Door) |
![]() |
Disconnect the power back door rod and remove the back door stay plate.
| 8. REMOVE BACK DOOR TRIM COVER LH (w/ Power Back Door) |
![]() |
Disengage the 2 clips and 2 claws, and remove the back door trim cover LH.
| 9. REMOVE BACK DOOR TRIM COVER RH |
![]() |
Disengage the 2 clips and 2 claws, and remove the back door trim cover RH.
| 10. REMOVE BACK DOOR LOCK COVER (for Glass Hatch Type) |
![]() |
Disengage the 2 claws and 4 guides, and remove the back door lock cover.
| 11. REMOVE ASSIST STRAP HOLE COVER |
![]() |
Disengage the 2 claws and 2 guides, and remove the assist strap hole cover.
| 12. REMOVE ASSIST STRAP ASSEMBLY |
![]() |
Remove the bolt and assist strap assembly.
| 13. REMOVE BACK DOOR TRIM PANEL ASSEMBLY |
![]() |
Disengage the 16 clips and remove the back door trim panel assembly.
| 14. REMOVE REAR WIPER SHAFT COVER (for Glass Hatch Type) |
![]() |
Disengage the 3 clips and remove the rear wiper shaft cover.
| 15. REMOVE REAR WIPER ARM HEAD CAP |
![]() |
Remove the rear wiper arm head cap.
| 16. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY |
![]() |
Remove the nut and the rear wiper arm and blade assembly.
| 17. REMOVE REAR WIPER LINK CAP (for Glass Hatch Type) |
![]() |
Remove the rear wiper link cap.
| 18. REMOVE REAR WIPER LINK PIVOT (for Glass Hatch Type) |
![]() |
Remove the nut and the rear wiper link pivot.
| 19. REMOVE REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type) |
When reinstalling the rear wiper motor assembly :
Open the glass hatch.
![]() |
Engage the 3 claws and 2 guides, and then install the centering jig.
![]() |
Close the glass hatch, and engage the 2 claws and guide.
![]() |
Disconnect the connector.
Remove the 2 nuts.
Remove the 4 bolts and the rear wiper motor assembly.
When using a new rear wiper motor assembly:
![]() |
Disconnect the connector.
Remove the 4 bolts.
![]() |
Remove the 2 nuts and the rear wiper motor assembly.
| 20. INSTALL REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type) |
![]() |
Temporarily install the rear wiper motor assembly with the 4 bolts and 2 nuts.
Tighten the 4 bolts and 2 nuts in the order shown in the illustration to install the rear wiper motor assembly.
Connect the connector.
| 21. INSTALL REAR WIPER LINK PIVOT (for Glass Hatch Type) |
![]() |
Install the rear wiper link pivot with the nut.
Open the glass hatch.
![]() |
Disengage the 2 guides.
Disengage the 3 claws and remove the centering jig.
Close the glass hatch.
| 22. INSTALL REAR WIPER LINK CAP (for Glass Hatch Type) |
![]() |
Apply MP grease to the entire surface of the rear wiper link cap.
![]() |
Install the rear wiper link cap.
| 23. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (for Glass Hatch Type) |
Stop the wiper motor at the automatic stop position.
![]() |
When reinstalling:
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush.
![]() |
Place the rear wiper arm and blade assembly so that the rear wiper blade is aligned with the ceramic line.
| Area | Dimension |
| A | 10 mm (0.39 in.) |
Install the rear wiper arm and blade assembly with the nut.
| 24. INSTALL REAR WIPER ARM HEAD CAP |
![]() |
Install the rear wiper arm head cap.
| 25. INSTALL REAR WIPER SHAFT COVER (for Glass Hatch Type) |
Open the glass hatch.
![]() |
Engage the 3 clips and install the rear wiper shaft cover.
Operate the rear wiper while spraying washer fluid on the glass. Make sure that the rear wiper functions properly and there is no interference with the vehicle body.
| 26. INSTALL BACK DOOR TRIM PANEL ASSEMBLY |
![]() |
Engage the 16 clips and install the back door trim panel assembly.
| 27. INSTALL ASSIST STRAP ASSEMBLY |
![]() |
Install the assist strap assembly with the bolt.
| 28. INSTALL ASSIST STRAP HOLE COVER |
![]() |
Engage the 2 guides and 2 claws, and install the assist strap hole cover.
| 29. INSTALL BACK DOOR LOCK COVER (for Glass Hatch Type) |
![]() |
Engage the 4 guides and 2 claws, and install the back door lock cover.
| 30. INSTALL BACK DOOR TRIM COVER LH (w/o Power Back Door) |
![]() |
Engage the 2 clips and 2 claws, and install the back door trim cover LH.
| 31. INSTALL BACK DOOR TRIM COVER LH (w/ Power Back Door) |
![]() |
Engage the 2 clips and 2 claws, and install the back door trim cover LH.
| 32. CONNECT POWER BACK DOOR ROD (w/ Power Back Door) |
![]() |
Install the back door stay plate and connect the power back door rod.
| 33. INSTALL BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door) |
![]() |
Engage the 6 claws and install the back door service hole cover LH.
| 34. INSTALL BACK DOOR TRIM COVER RH |
![]() |
Engage the 2 clips and 2 claws, and install the back door trim cover RH.
| 35. INSTALL BACK WINDOW UPPER TRIM PANEL ASSEMBLY |
![]() |
Engage the 4 clips and 4 claws, and install the back window upper trim panel assembly.