Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0111    Intake Air Temperature Sensor Gradient Too High

for Preparation Click here


DESCRIPTION

A132329E01
  1. The intake air temperature sensor, in the mass air flow meter, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature becomes low, the resistance of the thermistor increases. When the temperature becomes high, the resistance drops. These variations in resistance are transmitted to the ECM (included in the hybrid vehicle control ECU) as voltage changes (See Fig. 1).
  2. The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.
  3. Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, the voltage at terminal THA also varies according to changes in the intake air temperature. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

DTC No.
DTC Detection Condition
Trouble Area
P0111
When either condition below is met:
  1. The intake air temperature rise is large, from the previous trip warm-up to the following trip.
    (2 trip detection logic)
  2. The change in the intake air temperature after engine start is less than the threshold value.
Mass air flow meter

MONITOR DESCRIPTION

The ECM (included in the hybrid vehicle control ECU) performs OBD II monitoring based on the values from the intake air temperature sensor. If the change in the sensor value is not within the normal range, the ECM will not be able to perform OBD II monitoring or will misdiagnose that there is a malfunction in the sensor. The ECM detects the stuck intake air temperature sensor value by performing monitoring after the power switch is turned off or the engine is started (short soak or long soak).

MONITOR STRATEGY


Related DTCs
P0111: Intake air temperature sensor rationality (After engine stop)
P0111: Intake air temperature sensor rationality (After cold engine start)
Required Sensors/Components (Main)
Intake air temperature sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Once per driving cycle
Duration
5 hours or more
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs are not present
None

After engine stop: 
Time after engine start
10 seconds or more
Battery voltage
10.5 V or more
Engine coolant temperature sensor circuit
OK
Accumulated mass air flow amount before engine stop
3000 g or more
Key-off duration
30 minutes

After cold engine start: 
Key-off duration
5 hours
Time after engine start
10 seconds or more
Engine coolant temperature sensor circuit
OK
Engine coolant temperature
70°C (158°F) or more
Accumulated mass air flow amount
3000 g or more
Either of the following conditions 1 or 2 is met:
-
1. Duration while engine load is low
120 seconds or more
2. Duration while engine load is high
10 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


After engine stop: 
Intake air temperature change
Less than 1°C (1.8°F)

After cold engine start: 
Intake air temperature change
Less than 1°C (1.8°F)

WIRING DIAGRAM

Refer to DTC P0112 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0111)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0111 and other DTCs
    A
    P0111
    B

    HINT:
    If any DTCs other than P0111 are output, troubleshoot those DTCs first.



B
REPLACE MASS AIR FLOW METER (Click here)
A

GO TO DTC CHART