Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > Only Back Door LOCK / UNLOCK Functions do not Operate

for Preparation Click here


DESCRIPTION

  1. The main body ECU (instrument panel junction block) detects the condition of the back door opener switch.
  2. The main body ECU (instrument panel junction block) receives signals from the back door opener switch and activates the back door lock motor according to the signals.
  3. The main body ECU (instrument panel junction block) detects the condition of the back door courtesy switch.

WIRING DIAGRAM


B171386E11


INSPECTION PROCEDURE

1.SYSTEM CHECK
  1. Check if the vehicle is equipped with a back door closer system.

    Result:
    Result
    Proceed to
    w/ Back Door Closer System
    A
    w/o Back Door Closer System
    B



A
GO TO BACK DOOR CLOSER SYSTEM (Back Door cannot be Opened) (Click here)
B


2.READ VALUE USING TECHSTREAM (BACK DOOR OPENER SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus:
    Body Electrical / Main Body / Data List.

  1. Select Back Door Open Handle in the Data List and read the Techstream display.

    Main Body (Main Body ECU): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Open Handle SW
    Back door open handle signal/ON or OFF
    ON: Back door open handle switch is pushed
    OFF: Back door open handle switch is free
    -

    OK:
    On the tester screen, the item changes between ON and OFF according to the chart above.



NG
Go to step 5
OK


3.INSPECT BACK DOOR LOCK ASSEMBLY


    B164421E07
  1. Remove the back door lock assembly (Click here).

  1. Check operation of the door lock motor.

    1. Move the door lock to the lock position.

    2. Apply battery voltage to the door lock motor and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1
      Unlocked

  1. Check operation of the door courtesy switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      1 - 3
      Locked
      10 kΩ or higher
      1 - 3
      Unlocked
      Below 1 Ω



NG
REPLACE BACK DOOR LOCK ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK CIRCUIT)


  1. Disconnect the main body ECU (instrument panel junction block) connector.


    B203477E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    T3-2 (ACT+) - D8-1 (TR+)
    Always
    Below 1 Ω
    T3-2 (ACT+) - Body ground
    Always
    10 kΩ or higher
    T3-3 (D+) - D7-25 (BCTY)
    Always
    Below 1 Ω
    T3-3 (D+) - Body ground
    Always
    10 kΩ or higher
    T3-1 (ACT-) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK) 

5.INSPECT BACK DOOR OPENER SWITCH


    B178891E01
  1. Remove the back door opener switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    2 - 3
    Back door opener switch not pushed (OFF)
    10 kΩ or higher
    2 - 3
    Back door opener switch pushed (ON)
    Below 1 Ω



NG
REPLACE BACK DOOR OPENER SWITCH (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH CIRCUIT)


    B171388E03
  1. Disconnect the main body ECU (instrument panel junction block) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    h1-3 (B) - D8-26 (BDSU)
    Always
    Below 1 Ω
    h1-3 (B) - Body ground
    Always
    10 kΩ or higher
    h1-2 (L) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)