Home › BODY › ENGINE HOOD / DOOR › POWER BACK DOOR SYSTEM

POWER BACK DOOR SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)

H100802E05

  1. Disconnect the O15 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below:

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O15-10 (ECUB) - Body ground
    BR - Body ground
    ECUB power supply
    Always
    10 to 14 V
    O15-12 (B) - Body ground
    B - Body ground
    B power supply
    Always
    10 to 14 V
    O15-8 (IG) - Body ground
    GR - Body ground
    IG power supply
    power switch on (IG)
    10 to 14 V
    O15-8 (IG) - Body ground
    GR - Body ground
    IG power supply
    power switch off
    Below 1 V
    O15-17 (MSW) - Body ground
    V - Body ground
    Power back door main switch signal circuit
    Power back door main switch not pushed
    Below 1 Ω
    O15-17 (MSW) - Body ground
    V - Body ground
    Power back door main switch signal circuit
    Power back door main switch pushed
    10 kΩ or higher
    O15-20 (FUL) - Body ground
    LG - Body ground
    Back door courtesy light switch signal circuit
    Back door is opened
    Below 1 Ω
    O15-20 (FUL) - Body ground
    LG - Body ground
    Back door courtesy light switch signal circuit
    Back door is closed
    10 kΩ or higher
    O15-4 (DS1) - Body ground
    P - Body ground
    Back door closer switch signal circuit
    Back door closer switch ON
    Below 1 Ω
    O15-4 (DS1) - Body ground
    P - Body ground
    Back door closer switch signal circuit
    Back door closer switch OFF
    10 kΩ or higher
    O15-15 (OSL) - O15-14 (OSE)
    GR - Y
    Power back door touch sensor LH circuit
    Back door touch sensor LH not pressed
    Approx. 1 kΩ
    O15-15 (OSL) - O15-14 (OSE)
    GR - Y
    Power back door touch sensor LH circuit
    Back door touch sensor LH pressed
    Below 100 Ω
    O15-13 (OSR) - O15-14 (OSE)
    G - Y
    Power back door touch sensor RH circuit
    Back door touch sensor RH not pressed
    Approx. 1 kΩ
    O15-13 (OSR) - O15-14 (OSE)
    G - Y
    Power back door touch sensor RH circuit
    Back door touch sensor RH pressed
    Below 100 Ω
    O15-11 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the O15 ECU connector.

  4. Measure the voltage according to the value(s) in the table below:

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O15-26 (BZR+) - Body ground
    B - Body ground
    Power back door warning buzzer signal input
    Back door warning buzzer is sounding
    10 to 14 V
    O15-26 (BZR+) - Body ground
    B - Body ground
    Power back door warning buzzer signal input
    Back door warning buzzer is stopped
    Below 1 V
    O15-2 (DC+) - O15-1 (DC-)
    B - G
    Power back door lock motor circuit
    Back door lock motor is operating
    10 to 14 V
    O15-2 (DC+) - O15-1 (DC-)
    B - G
    Power back door lock motor circuit
    Back door lock motor is stopped
    Below 1 V
    O15-22 (HAF) - Body ground
    R - Body ground
    Back door lock half-latch switch signal circuit
    Back door is opened →
    Back door closer motor is operating →
    Back door is closed
    Below 1 V →
    10 to 14 V →
    Below 1 V
    O15-24 (POS) - Body ground
    LG - Body ground
    Back door lock position switch signal circuit
    Back door is opened →
    Back door closer motor is operating →
    Back door is closed
    Below 1 V →
    10 to 14 V →
    Below 1 V

    HINT:
    If the result is not as specified, the ECU may have a malfunction.


CHECK MAIN BODY ECU

B150879E05

  1. Disconnect the D7, 1F and 1M connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D7-2 (PBDS) - Body ground
    R - Body ground
    Power back door open / close switch signal circuit
    Power back door open / close switch ON
    Below 1 Ω
    D7-2 (PBDS) - Body ground
    R - Body ground
    Power back door open / close switch signal circuit
    Power back door open / close switch OFF
    10 kΩ or higher
    1F-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1M-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.