Home › BODY › ENGINE HOOD / DOOR › BACK DOOR CLOSER SYSTEM

BACK DOOR CLOSER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)

H100802E05

  1. Disconnect the O15 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O15-12 (B) - Body ground
    B - Body ground
    Battery power supply
    Always
    10 to 14 V
    O15-10 (ECUB) - Body ground
    BR - Body ground
    ECUB power supply
    Always
    10 to 14 V
    O15-8 (IG) - Body ground
    GR - Body ground
    IG power supply
    power switch on (IG)
    10 to 14 V
    O15-8 (IG) - Body ground
    GR - Body ground
    IG power supply
    power switch off
    Below 1 V
    O15-11 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the O15 ECU connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O15-2 (DC+) - O15-1 (DC-)
    B - G
    Back door lock motor circuit
    Back door lock motor is operating
    10 to 14 V
    O15-2 (DC+) - O15-1 (DC-)
    B - G
    Back door lock motor circuit
    Back door lock motor is not operating
    Below 1 V
    O15-20 (FUL) - Body ground
    LG - Body ground
    Back door courtesy switch circuit
    Back door is closed
    10 to 14 V
    O15-20 (FUL) - Body ground
    LG - Body ground
    Back door courtesy switch circuit
    Back door is open
    Below 1 V
    O15-22 (HAF) - Body ground
    R - Body ground
    Back door lock half-latch switch signal circuit
    Back door is open → Back door closer motor → Back door is closed
    Below 1 V → 10 to 14 V → Below 1 V
    O15-24 (POS) - Body ground
    LG - Body ground
    Back door lock position switch signal circuit
    Back door is open → Back door closer operates → Back door is closed
    Below 1 V → 10 to 14 V → Below 1 V
    If the result is not as specified, the ECU may have a malfunction.


CHECK MAIN BODY ECU

B150879E05

  1. Disconnect the D7, D8, 1F and 1M connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D8-26 (BDSU) - Body ground
    Y - Body ground
    Back door open switch signal circuit
    Back door open switch ON
    Below 1 Ω
    D8-26 (BDSU) - Body ground
    Y - Body ground
    Back door open switch signal circuit
    Back door open switch OFF
    10 kΩ or higher
    D7-2 (PBDS) - Body ground
    R - Body ground
    Power back door open / close switch signal circuit
    Power back door open / close switch ON
    Below 1 Ω
    D7-2 (PBDS) - Body ground
    R - Body ground
    Power back door open / close switch signal circuit
    Power back door open / close switch OFF
    10 kΩ or higher
    1F-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1M-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.