REAR BLOWER MOTOR > INSTALLATION |
| 1. INSTALL REAR BLOWER MOTOR SUB-ASSEMBLY |
![]() |
Install the rear blower motor sub-assembly with the 3 screws.
Connect the connector.
| 2. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH |
| 3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH |
Engage the 4 clips and the 7 claws.
Install the 2 clips.
Install the deck trim side panel assembly RH with the 3 bolts.

| 4. INSTALL FRONT DECK SIDE TRIM COVER RH |
| 5. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK |
| 6. INSTALL ROPE HOOK ASSEMBLY (for RH Side) |
| 7. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH |
![]() |
Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.
| 8. INSTALL SIDE TRIM COVER RH (for Manual Air Conditioning System) |
![]() |
Engage the 4 claws, and install the side trim cover RH.
| 9. INSTALL REAR ROOM TEMPERATURE SENSOR (for Automatic Air Conditioning System) |
Connect the connector.
![]() |
Engage the 4 claws and install the rear room temperature sensor.
| 10. INSTALL DECK SIDE TRIM RH |
| 11. INSTALL DECK SIDE TRIM COVER RH |
| 12. INSTALL REAR SEAT SIDE GARNISH CAP |
![]() |
Engage the guide and the 6 claws.
Install the rear seat side garnish cap with the screw.
| 13. INSTALL REAR FLOOR FINISH PLATE |
![]() |
Engage the 4 clips and the 4 claws, and install the rear floor finish plate.
| 14. INSTALL REAR NO. 2 SEAT ASSEMBLY |
![]() |
Install the rear No. 2 seat assembly with the 4 bolts.
| 15. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH |
![]() |
Install the rear seat lap type belt assembly LH with the bolt.
| 16. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH |
Install the rear seat lap type belt assembly RH with the bolt.
| 17. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY |
![]() |
Install the rear No. 2 seat inner belt assembly with the bolt.
| 18. INSTALL REAR MAT |
![]() |
Install the rear mat.
| 19. INSTALL DECK FLOOR BOARD ASSEMBLY |
![]() |
Install the 2 nuts and the deck floor board assembly.
Engage the 3 claws.
| 20. INSTALL DECK SIDE TRIM BOX LH |
Install the deck side trim box LH as shown in the illustration.

![]() |
Install the 2 deck side trim clip and the clips.
| 21. INSTALL REAR SEAT SIDE COVER LH |
![]() |
Engage the 2 clips and install the rear seat side cover LH.
| 22. INSTALL DECK SIDE TRIM BOX RH |
Install the deck side trim box RH as shown in the illustration.

![]() |
Install the 2 deck side trim clip and the clips.
| 23. INSTALL JACK CARRIER ASSEMBLY |
![]() |
Engage the 3 claws, and install the jack carrier assembly.
| 24. INSTALL JACK ASSEMBLY |
![]() |
Install the jack assembly.
| 25. INSTALL JACK CARRIER CUSHION |
![]() |
Install the jack carrier cushion.
| 26. INSTALL JACK CARRIER SUPPORT |
| 27. INSTALL REAR SEAT SIDE COVER RH |
![]() |
Engage the 2 clips and install the rear seat side cover RH.
| 28. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Install the tonneau cover assembly.
| 29. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY |
![]() |
Engage the 2 guides and install the No. 2 deck board sub-assembly.
| 30. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY |
![]() |
Engage the 2 guides and install the No. 3 deck board sub-assembly.
| 31. INSTALL DECK BOARD ASSEMBLY |
![]() |
Install the deck board assembly.
| 32. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
| 33. INSTALL REAR DOOR SCUFF PLATE RH |