Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR MIX CONTROL SERVO MOTOR (for Rear)

AIR MIX CONTROL SERVO MOTOR (for Rear) > INSTALLATION

for Preparation Click here



1. INSTALL REAR AIR MIX CONTROL SERVO MOTOR SUB-ASSEMBLY


    E150363E01
  1. Using the reference point, install the rear air mix control servo motor sub-assembly with the 2 screws.

  1. Connect the connector.



2. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
  1. Engage the 4 clips and the 7 claws.

  1. Install the 2 clips.



  1. Install the deck trim side panel assembly RH with the 3 bolts.


    B173622



4. INSTALL FRONT DECK SIDE TRIM COVER RH

HINT:
Use the same procedure for the RH side and the LH side.



5. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

HINT:
Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.



6. INSTALL ROPE HOOK ASSEMBLY (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.



7. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH


    B173619
  1. Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.



8. INSTALL SIDE TRIM COVER RH (for Manual Air Conditioning System)


    B173610
  1. Engage the 4 claws, and install the side trim cover RH.



9. INSTALL REAR ROOM TEMPERATURE SENSOR (for Automatic Air Conditioning System)
  1. Connect the connector.



    E150364
  1. Engage the 4 claws and install the rear room temperature sensor.



10. INSTALL DECK SIDE TRIM RH

HINT:
Use the same procedure for the RH side and the LH side.



11. INSTALL DECK SIDE TRIM COVER RH

HINT:
Use the same procedure for the RH side and the LH side.



12. INSTALL REAR SEAT SIDE GARNISH CAP


    B173617
  1. Engage the guide and the 6 claws.

  1. Install the rear seat side garnish cap with the screw.



13. INSTALL REAR FLOOR FINISH PLATE


    B173609
  1. Engage the 4 clips and the 4 claws, and install the rear floor finish plate.



14. INSTALL REAR NO. 2 SEAT ASSEMBLY


    B173781
  1. Install the rear No. 2 seat assembly with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



15. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH


    B170936
  1. Install the rear seat lap type belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.



16. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH
  1. Install the rear seat lap type belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.



17. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY


    B170935
  1. Install the rear No. 2 seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 2 seat inner belt assembly to overlap the protruding part of the rear No. 2 seat bracket.

    HINT:
    Use the same procedure for the RH side and LH side.



18. INSTALL REAR MAT


    B173249
  1. Install the rear mat.



19. INSTALL DECK FLOOR BOARD ASSEMBLY


    B178561
  1. Install the 2 nuts and the deck floor board assembly.

  1. Engage the 3 claws.



20. INSTALL DECK SIDE TRIM BOX LH


  1. Install the deck side trim box LH as shown in the illustration.


    B178555



    B173243E01
  1. Install the 2 deck side trim clip and the clips.



21. INSTALL REAR SEAT SIDE COVER LH


    B173607
  1. Engage the 2 clips and install the rear seat side cover LH.



22. INSTALL DECK SIDE TRIM BOX RH


  1. Install the deck side trim box RH as shown in the illustration.


    B178553



    B173247E01
  1. Install the 2 deck side trim clip and the clips.



23. INSTALL JACK CARRIER ASSEMBLY


    B178549
  1. Engage the 3 claws, and install the jack carrier assembly.



24. INSTALL JACK ASSEMBLY


    B173245
  1. Install the jack assembly.



25. INSTALL JACK CARRIER CUSHION


    B178550
  1. Install the jack carrier cushion.



26. INSTALL JACK CARRIER SUPPORT


27. INSTALL REAR SEAT SIDE COVER RH


    B173608
  1. Engage the 2 clips and install the rear seat side cover RH.



28. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Install the tonneau cover assembly.



29. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    B173244
  1. Engage the 2 guides and install the No. 2 deck board sub-assembly.



30. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    B173242
  1. Engage the 2 guides and install the No. 3 deck board sub-assembly.



31. INSTALL DECK BOARD ASSEMBLY


    B173240
  1. Install the deck board assembly.



32. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B173237E01
  1. Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

    NOTICE:
    After installation, check that the corners fit correctly.



33. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.