Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › ENGINE COOLANT TEMPERATURE SENSOR

ENGINE COOLANT TEMPERATURE SENSOR > INSTALLATION

for Preparation Click here



1. INSTALL ENGINE COOLANT TEMPERATURE SENSOR
  1. Install a new gasket onto the engine coolant temperature sensor.



    A173523
  1. Install the engine coolant temperature sensor.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the engine coolant temperature sensor connector.



2. INSTALL AIR CLEANER BRACKET


    A108129
  1. Install the 2 bolts and air cleaner bracket.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



3. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    A173493
  1. Align the tab on the throttle body with the groove on the air cleaner hose and tighten the hose clamp.



    A173492
  1. Install the air cleaner case sub-assembly with the 5 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    A173491
  1. Connect the intake air flow meter connector.

  1. Connect the 2 wire harness clamps to the air cleaner case.



    A173490
  1. Connect the No. 1 ventilation hose.



4. INSTALL AIR CLEANER CAP SUB-ASSEMBLY
  1. Install the air cleaner filter element to the air cleaner case sub-assembly.



    A173489
  1. Install the air cleaner cap sub-assembly with the 4 clamps and 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



5. INSTALL NO. 2 ENGINE ROOM SIDE COVER LH


    A173813
  1. Fit the clips and install the No. 2 engine room side cover LH.

    NOTICE:
    1. Be sure to engage the clips securely.
    2. Do not apply excessive force or do not hit the cover to engage the clips. This may cause the cover to break.



6. INSTALL COOL AIR INTAKE DUCT SEAL
  1. Install the cool air intake duct seal with the 11 clips.



7. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY


    C175030E01
  1. Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.

    Torque:
    Nut A:
    85 N*m{ 866 kgf*cm , 63 ft.*lbf }
    Bolt B:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
    Nut C:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



    C175029
  1. Engage the 4 clamps.



8. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E150150
  1. Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.



9. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


  1. Engage the 20 claws.


    E150149

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.



    E150146
  1. Engage the 2 claws and connect the front fender to cowl side seal LH.



    E150147
  1. Engage the 2 claws and connect the front fender to cowl side seal RH.



10. INSTALL HOOD TO COWL TOP SEAL


    E150148
  1. Engage the 8 clips and install the hood to cowl top seal.



11. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



  1. When reinstalling:



      E112237E01
    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.



    E147125E01
  1. Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    25.6 mm (1.00 in.)



12. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



  1. When reinstalling:



      E112237E01
    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.



    E152618E01
  1. Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    31.9 mm (1.26 in.)

  1. Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.