Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2420    Evaporative Emission System Switching Valve Control Circuit High

for Preparation Click here


DTC SUMMARY


DTCs
Monitoring Item
Malfunction Detection Condition
Trouble Area
Detection Timing
Detection Logic
P2420
Vent valve stuck open (vent)
Vent valve open stuck is detected during EVAP key-off monitor
  1. Canister pump module (Reference orifice, leak detection pump, vent valve)
  2. Connector / wire harness (Canister pump module - Hybrid vehicle control ECU)
  3. Hybrid vehicle control ECU
Power switch OFF
2 trip

DESCRIPTION

Refer to EVAP System .

INSPECTION PROCEDURE

Refer to EVAP System .

MONITOR DESCRIPTION

Vent valve stuck open (vent)
In operation C, the vent valve turns ON (closes) and the EVAP system pressure is then measured by the ECM, using the canister pressure sensor, to conduct an EVAP leak check. If the pressure does not increase when the vent valve is opened, the ECM interprets this as the vent valve being stuck open. The ECM illuminates the MIL and sets the DTC.

A141250E02


MONITOR STRATEGY


Required Sensors/Components (Main)
Purge VSV and canister pump module
Frequency of Operation
Once per driving cycle
Duration
Within 15 minutes
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None
EVAP key-off monitor runs when all of the following conditions are met:
-
Atmospheric pressure
70 to 110 kPa (525 to 825 mmHg)
Battery voltage
10.5 V or more
Vehicle speed
Below 2.5 mph (4 km/h)
Power switch
OFF
Engine condition
Not running
Canister pressure sensor malfunction (P0450, P0451, P0452 and P0453)
Not detected
FTP sensor malfunction (P1451, P1452 and P1453)
Not detected
Purge VSV
Not operated by scan tool
Vent valve
Not operated by scan tool
Leak detection pump
Not operated by scan tool
Both of the following conditions are met before power switch off
Conditions 1 and 2
1. Duration that vehicle is being driven
5 minutes or more
2. Purge flow
Executed
Engine coolant temperature
4.4 to 35°C (40 to 95°F)
Intake air temperature
4.4 to 35°C (40 to 95°F)
Time after engine stopped
5 hours

Example of restart time 
First time
7 hours
Second time
9 hours and 30 minutes
  1. Key-off monitor sequence 1 to 15

    1. Atmospheric pressure measurement 
    Next sequence is run if the following condition is met:
    -
    Atmospheric pressure change for 10 seconds
    Less than 0.3 kPa (2.25 mmHg) for 1 second

    2. First reference pressure measurement 
    Next sequence is run if all of the following conditions are met:
    Conditions 1, 2 and 3
    1. EVAP pressure 1.9 seconds after reference pressure measurement
    -1 kPa (-7.5 mmHg) or less
    2. Reference pressure
    -4.85 to -1.057 kPa (-36.4 to -7.93 mmHg)
    3. Reference pressure
    Saturated

    3. Vent valve stuck closed check 
    Next sequence is run if the following condition is met:
    -
    EVAP pressure change for 10 seconds after vent valve ON (Closed)
    0.3 kPa (2.25 mmHg) or more

    4. Vacuum introduction for canister 
    Next sequence is run if the following condition is met:
    -
    Vacuum introduction time
    15 minutes or less

    5. Purge VSV stuck closed check 
    Next sequence is run if the following condition is met:
    -
    EVAP pressure change for 10 seconds after purge VSV ON (Open).
    0.3 kPa (2.25 mmHg) or more

    6. Second reference pressure measurement 
    Next sequence is run if all of the following conditions are met:
    Conditions 1, 2, 3 and 4
    1. EVAP pressure 1.9 seconds after reference pressure measurement
    -1 kPa (-7.5 mmHg) or less
    2. Reference pressure
    -4.85 to -1.057 kPa (-36.4 to -7.93 mmHg)
    3. Reference pressure
    Saturated
    4. Reference pressure difference between the first and second
    Less than 0.7 kPa (5.25 mmHg)

    7. Canister leak 
    Next sequence is run if the following condition is met:
    -
    Canister leaks when vacuum introduction was complete
    Second reference pressure or less

    8. Fuel vapor-containment valve (FVCV stuck closed check) 
    Next sequence is run if both of the following conditions are met:
    Conditions 1 and 2
    1. FTP when EVAP monitor started
    -2 kPa (-15 mmHg) or less, or 3 kPa (22.5 mmHg) or more
    2. FTP change while FVCV and vent valve are open
    0.5 kPa (3.75 mmHg) or more

    9. Vacuum introduction for fuel tank 
    Next sequence is run if both of the following conditions are met:
    Conditions 1 and 2
    1. FTP when EVAP monitor started
    -2 to 3 kPa (-15 to 22.5 mmHg)
    2. Vacuum introduction time
    15 minutes or less

    10. FVCV stuck closed check 
    Next sequence is run if the following condition is met:

    FTP change when vacuum introduction for fuel tank
    0.5 kPa (3.75 mmHg)

    11. FTP sensor stuck check 
    Next sequence is run if the following condition is met:

    FTP change when FVCV closed
    0.35 kPa (2.6 mmHg) or less

    12 Third reference pressure measurement 
    Next sequence is run if all of the following conditions are met:
    Conditions 1, 2, 3, and 4
    1. FTP 1.9 seconds after reference pressure measurement
    -1 kPa (-7.5 mmHg) or less
    2. Reference pressure
    -4.85 to -1.057 kPa (-36.4 to -7.93 mmHg)
    3. Reference pressure
    Saturated
    4. Reference pressure difference between the second and third
    Less than 0.7 kPa (5.25 mmHg)

    13. Fuel tank leak check 
    Sequence is run if the following condition is met:

    FTP when vacuum introduction for fuel tank was complete
    Less than third reference pressure

    14. FTP sensor stuck check 
    Next sequence is run if the following condition is met:
    -
    FTP change while FVCV and vent valve are open
    Less than 0.3 kPa (2.25 mmHg)

    15. Atmospheric pressure measurement 
    Monitor is complete if the following condition is met:
    -
    Atmospheric pressure difference between sequence 1 and 8
    0.35 kPa (2.6 mmHg) or less

TYPICAL MALFUNCTION THRESHOLDS

"Saturated" indicates that the EVAP pressure change is less than 0.286 kPa (2.14 mmHg) in 60 seconds.

Vent valve stuck open (vent) 
EVAP pressure change after EVAP canister vent valve is ON
Less than 0.3 kPa (2.25 mmHg)

MONITOR RESULT

Refer to CHECKING MONITOR STATUS .