Home › BRAKE › BRAKE › BRAKE PEDAL

BRAKE PEDAL > ADJUSTMENT

for Preparation Click here



1. INSPECT AND ADJUST BRAKE PEDAL HEIGHT


  1. Check the brake pedal height.



      C170606E01
    1. Turn back the carpet.

    2. Measure the shortest distance between the brake pedal surface and tibia pad.

      Pedal height from tibia pad:
      148.8 to 158.8 mm (5.858 to 6.252 in.)

  1. Adjust the brake pedal height.

    1. Disconnect the stop light switch connector.

    2. Remove the stop light switch assembly.

    3. Loosen the push rod clevis lock nut.

    4. Adjust the brake pedal height by turning the push rod.

    5. Tighten the push rod clevis lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    6. Install and adjust the stop light switch .

      NOTICE:
      Do not depress the brake pedal.

    7. Connect the stop light switch connector.



2. ADJUST BRAKE PEDAL STROKE SENSOR

NOTICE:
Do not drop the sensor. If the sensor has been dropped, replace the brake pedal stroke sensor with a new one.



  1. When installing a new brake pedal stroke sensor assembly:

    NOTICE:
    Do not break the sensor lever set pin before installing the brake pedal stroke sensor with the bolts. If the sensor lever set pin breaks while tightening a bolt, do not use that sensor.




      C174573E01
    1. Connect the sensor connector.

    2. Install a new sensor with the 2 bolts.

      Torque:
      9.3 N*m{ 95 kgf*cm , 82 in.*lbf }

      NOTICE:
      1. Engage the sensor lever with the brake pedal groove.
      2. Check that there is no foreign matter attached to the contact surface of the sensor.
      3. Check that the tip of the sensor lever is protruding from the brake pedal groove.

    3. Firmly depress the brake pedal and break the sensor lever set pin.

    4. Remove the broken lever set pin.



  1. When reusing the brake pedal stroke sensor assembly:

    1. Connect the sensor connector.



    2. C171426E01
    3. Temporarily install the sensor with the 2 bolts.

      NOTICE:
      1. Engage the sensor lever with the brake pedal groove.
      2. Check that there is no foreign matter attached to the contact surface of the sensor.

    4. Connect the cable to the negative battery terminal.

    5. Connect the Techstream to the DLC3.



    6. C171423
    7. Turn the power switch on (IG). Reading the value of the stroke sensor shown in Data List, turn the sensor slowly to the right and left to adjust the output voltage to the standard voltage.

      Standard voltage:

      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Stroke Sensor
      Stroke sensor /
      min.: 0 V, max.: 5 V
      When brake pedal is released:
      0.7 to 1.3 V
      -

    8. Tighten the 2 bolts.

      Torque:
      9.3 N*m{ 95 kgf*cm , 82 in.*lbf }

      NOTICE:
      Do not depress the brake pedal after turning the power switch on (IG).

    9. Disconnect the cable from the negative battery terminal.

    10. Disconnect the Techstream.



3. INSPECT BRAKE PEDAL FREE PLAY


    C132708E01
  1. Depress the pedal until a slight resistance is felt. Measure the distance as shown in the illustration.

    Pedal free play:
    1.0 to 2.0 mm (0.039 to 0.078 in.)

    If the pedal free play is not as specified, check the stop light switch clearance . If the pedal free play is as specified, proceed to the "INSPECT BRAKE PEDAL RESERVE DISTANCE" procedure.



4. INSPECT BRAKE PEDAL RESERVE DISTANCE

HINT:
Measure the distance at the same point used for the brake pedal height inspection.



    C111339E05
  1. Release the parking brake lever.

  1. With the engine running, depress the brake pedal and measure the pedal reserve distance as shown in the illustration.

    Pedal reserve distance from the tibia pad at 500 N (51 kgf, 112 lbf):
    95 mm (3.74 in.)

    If the distance is not as specified, troubleshoot the brake system (Click here).