Home › BODY ELECTRICAL › DOOR LOCK › SMART KEY SYSTEM

SMART KEY SYSTEM > Driver Side Door Entry Unlock Function does not Operate

for Preparation Click here


DESCRIPTION

If the driver door entry unlock function does not operate but the entry lock function operates, the communication line between the vehicle and electrical key transmitter is normal. As a faulty part, the touch sensor circuit (certification ECU (smart key ECU assembly) → driver side door outside handle → driver side door electrical key oscillator) can be considered.

WIRING DIAGRAM


B164404E06


INSPECTION PROCEDURE

NOTICE:
Before performing the inspection, check that there are no problems related to "CAN COMMUNICATION SYSTEM" and "LIN COMMUNICATION SYSTEM".

1.CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the master switch assembly is operated, check that the locked doors unlock (Click here).

    OK:
    Locked doors unlock.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2.READ VALUE ON TECHSTREAM (DOOR OUTSIDE HANDLE)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus:
    Body Electrical / Smart Key / Data List.

  1. Select D-Door Touch Sensor in the Data List and read the Techstream display.

    Smart Key (Certification ECU (Smart Key ECU Assembly)): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D-Door Touch Sensor
    Status of touch sensor front LH / ON or OFF
    ON: Touch sensor is touched
    OFF: Touch sensor is not touched
    -

    OK:
    On the tester screen, the item changes between ON and OFF according to the chart above.



NG
Go to step 3
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (Click here)  

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR)


    B171407E01
  1. Disconnect the certification ECU (smart key ECU assembly) and door electrical key oscillator connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D40-5 (SEL1) - z14-4 (SEL)
    Always
    Below 1 Ω
    D40-22 (SEN1) - z14-6 (SENS)
    Always
    Below 1 Ω
    D40-5 (SEL1) - Body ground
    Always
    10 kΩ or higher
    D40-22 (SEN1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - FRONT DOOR OUTSIDE HANDLE)
  1. Remove the front door outside handle (Click here).



    B164339E23
  1. Disconnect the touch sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    z13-6 (SGT) - z14-2 (SGT)
    Always
    Below 1 Ω
    z13-6 (SGT) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE DOOR ELECTRICAL KEY OSCILLATOR
  1. Replace the door electrical key oscillator (Click here).


NEXT


6.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
  1. Check that the entry functions operate normally.

    OK:
    Entry functions operate normally.



NG
Go to step 7
OK

END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE) 

7.REPLACE FRONT DOOR OUTSIDE HANDLE
  1. Replace the front door outside handle RH (Click here).


NEXT


8.CHECK FRONT DOOR OUTSIDE HANDLE (OPERATION)
  1. Check that the entry functions operate normally.

    OK:
    Entry functions operate normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (Click here)
OK

END (FRONT DOOR OUTSIDE HANDLE IS DEFECTIVE)