Home › ENGINE › 3MZ-FE COOLING › COOLING FAN SYSTEM

COOLING FAN SYSTEM > Cooling Fan Circuit

for Preparation Click here


DESCRIPTION

The hybrid vehicle control ECU calculates an appropriate cooling fan speed based on the engine coolant temperature, air conditioning switch condition, refrigerant pressure, engine speed, and vehicle speed and sends the signals to the cooling fan ECU to regulate the cooling fan. The cooling fan ECU controls the cooling fan speed based on the duty ratio signal sent from the hybrid vehicle control ECU. By basing its control on the operating conditions, the hybrid vehicle control ECU can control the fan speed optimally using the cooling fan ECU, achieving both high cooling performance and quietness. The cooling fan speed is determined based on engine coolant temperature, air conditioner operating conditions, engine speed, and vehicle speed.

INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cooling Fan.

  1. Check the operation of the cooling fan while operating it using the Techstream.

    Result:
    Result
    Proceed to
    Both cooling fan motors operate.
    A
    Neither of cooling fan motors operates.
    B
    Only cooling fan motor does not operate.
    C
    Only No. 2 cooling fan motor does not operate.
    D



B
Go to step 2

C
Go to step 6

D
Go to step 17
A

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

2.CHECK HARNESS AND CONNECTOR (NO. 1 FAN MAIN RELAY - BODY GROUND)
  1. Turn the power switch on (IG).



    A179244E01
  1. Remove the NO. 1 FAN MAIN relay from the engine room relay block and junction block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (NO. 1 FAN MAIN relay) - Body ground
    Power switch on (IG)
    11 to 14 V



NG
Go to step 4
OK


3.CHECK HARNESS AND CONNECTOR (NO. 1 FAN MAIN RELAY - BODY GROUND)


    A179244E01
  1. Remove the NO. 1 FAN MAIN relay from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (NO. 1 FAN MAIN relay) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

4.INSPECT FUSE (NO. 2 A/C FUSE)


    A179252E01
  1. Remove the NO. 2 A/C fuse from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    NO. 2 A/C fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE (NO. 2 A/C FUSE)
OK


5.CHECK HARNESS AND CONNECTOR (NO. 1 FAN MAIN RELAY - NO. 2 A/C FUSE)


    A179289E01
  1. Remove the NO. 1 FAN MAIN relay from the engine room relay block and junction block.

  1. Remove the NO. 2 A/C fuse from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    1 (NO. 1 FAN MAIN relay) - 2 (NO. 2 A/C fuse)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    1 (NO. 1 FAN MAIN relay) and 2 (NO. 2 A/C fuse) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK SMART KEY SYSTEM 

6.CHECK COOLING FAN SYSTEM
  1. Disconnect the A43 hybrid vehicle control ECU connector.

  1. Turn the power switch on (IG).

  1. Check the operation of the cooling fan.

    OK:
    The cooling fan motor rotates.



NG
Go to step 7
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

7.INSPECT COOLING FAN MOTOR


    A159758E07
  1. Disconnect the cooling fan motor connector.

  1. Connect the battery positive terminal to terminal 2 of the cooling fan connector, and connect the battery negative terminal to terminal 1 of the cooling fan motor connector.

    OK:
    The cooling fan motor rotates.



NG
REPLACE COOLING FAN MOTOR (Click here)
OK


8.CHECK COOLING FAN ECU (POWER SOURCE)


    A148766E10
  1. Disconnect the cooling fan ECU connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A9-1 (+B1) - Body ground
    Power switch on (IG)
    11 to 14 V



NG
Go to step 11
OK


9.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)


    A148766E11
  1. Disconnect the cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A9-3 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - HYBRID VEHICLE CONTROL ECU)


    A179300E01
  1. Disconnect the A43 connector from the hybrid vehicle control ECU.

  1. Disconnect the cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    A43-14 (RFC1) - A9-2 (SI)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    A43-14 (RFC1) and A9-2 (SI) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COOLING FAN ECU (Click here)  

11.CHECK FUSIBLE LINK BLOCK ASSEMBLY (NO. 1 FAN FUSE)


    A179475E01
  1. Remove the fusible link block assembly from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1- 2 (NO. 1 FAN fuse)
    Always
    Below 1 Ω



NG
REPLACE FUSE (NO. 1 FAN FUSE)
OK


12.INSPECT COOLING FAN RELAY (NO. 1 FAN MAIN RELAY)


    A169410
  1. Remove the NO. 1 FAN MAIN relay from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Battery voltage is applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE COOLING FAN RELAY (NO. 1 FAN MAIN RELAY)
OK


13.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - NO. 1 FAN MAIN RELAY)


    A179482E01
  1. Disconnect the cooling fan ECU connector.

  1. Remove the NO. 1 FAN MAIN relay from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    A9-3 (E1) - 2 (NO. 1 FAN MAIN relay)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    A9-3 (E1) and 2 (NO. 1 FAN MAIN relay) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.CHECK HARNESS AND CONNECTOR (NO. 1 FAN MAIN RELAY - NO. 2 A/C FUSE)


    A179289E01
  1. Remove the NO. 1 FAN MAIN relay from the engine room relay block and junction block.

  1. Remove the NO. 2 A/C fuse from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    1 (NO. 1 FAN MAIN relay) - 2 (NO. 2 A/C fuse)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    1 (NO. 1 FAN MAIN relay) and 2 (NO. 2 A/C fuse) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - NO. 1 FAN MAIN RELAY)


    A179482E02
  1. Disconnect the cooling fan ECU connector.

  1. Remove the NO. 1 FAN MAIN relay from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    A9-1 (+B1) - 5 (NO. 1 FAN MAIN relay)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    A9-1 (+B1) and 5 (NO. 1 FAN MAIN relay) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16.CHECK HARNESS AND CONNECTOR (NO. 1 FAN MAIN RELAY - NO. 1 FAN FUSE)


    A179485E01
  1. Remove the NO. 1 FAN MAIN relay from the engine room relay block and junction block.

  1. Remove the fusible link block assembly from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    3 (NO. 1 FAN MAIN relay) - 2 (NO. 1 FAN fuse)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    3 (NO. 1 FAN MAIN relay) and 2 (NO. 1 FAN fuse) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK SMART KEY SYSTEM 

17.CHECK COOLING FAN SYSTEM
  1. Disconnect the A43 hybrid vehicle control ECU connector.

  1. Turn the power switch on (IG).

  1. Check the operation of the cooling fan.

    OK:
    The No. 2 cooling fan motor rotates.



NG
Go to step 7
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

18.INSPECT NO. 2 COOLING FAN MOTOR


    A159758E08
  1. Disconnect the No. 2 cooling fan motor connector.

  1. Connect the battery positive terminal to terminal 2 of the cooling fan connector, and connect the battery negative terminal to terminal 1 of the No. 2 cooling fan motor connector.

    OK:
    The No. 2 cooling fan motor rotates.



NG
REPLACE NO. 2 COOLING FAN MOTOR
OK


19.CHECK COOLING FAN ECU (POWER SOURCE)


    A148766E18
  1. Disconnect the No. 2 cooling fan ECU connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A41-1 (+B2) - Body ground
    Power switch on (IG)
    11 to 14 V



NG
Go to step 11
OK


20.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN ECU - BODY GROUND)


    A148766E19
  1. Disconnect the No. 2 cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A41-3 (E2) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


21.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN ECU - HYBRID VEHICLE CONTROL ECU)


    A179300E03
  1. Disconnect the A43 connector from the hybrid vehicle control ECU.

  1. Disconnect the No. 2 cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    A43-10 (RFC2) - A41-2 (SI2)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    A43-10 (RFC2) and A41-2 (SI2) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COOLING FAN ECU (NO. 2) (Click here)  

22.CHECK FUSIBLE LINK BLOCK ASSEMBLY (NO. 2 FAN FUSE)


    A179475E03
  1. Remove the fusible link block assembly from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1- 2 (NO. 2 FAN fuse)
    Always
    Below 1 Ω



NG
REPLACE FUSE (NO. 2 FAN FUSE)
OK


23.INSPECT COOLING FAN RELAY (NO. 2 FAN MAIN RELAY)


    A169410
  1. Remove the NO. 2 FAN MAIN relay from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Battery voltage is applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE COOLING FAN RELAY (NO. 2 FAN MAIN RELAY)
OK


24.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN ECU - NO. 2 FAN MAIN RELAY)


    A179545E04
  1. Disconnect the No. 2 cooling fan ECU connector.

  1. Remove the NO. 2 FAN MAIN relay from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    A41-3 (E2) - 2 (NO. 2 FAN MAIN relay)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    A41-3 (E2) and 2 (NO. 2 FAN MAIN relay) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


25.CHECK HARNESS AND CONNECTOR (NO. 2 FAN MAIN RELAY - NO. 2 A/C FUSE)


    A179548E01
  1. Remove the NO. 2 FAN MAIN relay from the engine room relay block and junction block.

  1. Remove the NO. 2 A/C fuse from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    1 (NO. 2 FAN MAIN relay) - 2 (NO. 2 A/C fuse)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    1 (NO. 2 FAN MAIN relay) and 2 (NO. 2 A/C fuse) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


26.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN ECU - NO. 2 FAN MAIN RELAY)


    A179545E02
  1. Disconnect the cooling fan ECU connector.

  1. Remove the NO. 2 FAN MAIN relay from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    A41-1 (+B1) - 5 (NO. 2 FAN MAIN relay)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    A41-1 (+B1) and 5 (NO. 2 FAN MAIN relay) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


27.CHECK HARNESS AND CONNECTOR (NO. 2 FAN MAIN RELAY - NO. 2 FAN FUSE)


    A179549E01
  1. Remove the NO. 2 FAN MAIN relay from the engine room relay block and junction block.

  1. Remove the fusible link block assembly from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    3 (NO. 2 FAN MAIN relay) - 2 (NO. 2 FAN fuse)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    3 (NO. 2 FAN MAIN relay) and 2 (NO. 2 FAN fuse) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK SMART KEY SYSTEM