LIN COMMUNICATION SYSTEM > TERMINALS OF ECU |
| CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
Disconnect the D7, D8, 1D and 1F instrument panel junction block assembly connectors.

Measure the voltage and resistance between the wire harness side connectors and body ground.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| D8-6 (AM1) - Body ground | GR - Body ground | Battery power supply | Always | 11 to 14 V |
| D7-1 (AM2) - Body ground | B - Body ground | Battery power supply | Always | 11 to 14 V |
| 1F-10 (GND1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the D7, D8, 1D and 1F instrument panel junction block assembly connectors.
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| 1E-7 (LIN1) - 1F-10 (GND1) | R - W-B | LIN Communication line | power switch on (IG) | Pulse generation |
| D9-10 (LIN2) - 1F-10 (GND1) | P - W-B | LIN Communication line | power switch on (IG) | Pulse generation |
| CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side) |

Disconnect the H1 motor connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| H1-2 (B) - H1-1 (E) | SB - W-B | Battery power supply | Always | 11 to 14 V |
| H1-1 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the H1 motor connector.
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| H1-9 (LIN) - H1-1 (E) | P - W-B | LIN Communication line | power switch on (IG) | Pulse generation |
| CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) [w/ Sliding Roof] |

Disconnect the Q12 ECU connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| Q12-1 (B) - Q12-2 (E) | B - W-B | Battery power supply | Always | 11 to 14 V |
| Q12-2 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the Q12 ECU connector.
Measure the pulse according to value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| Q12-4 (MPX1) - Q12-2 (E) | P - W-B | LIN Communication line | power switch on (IG) | Pulse generation |
| CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [w/ Smart Key System] |

Disconnect the D40 ECU connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| D40-1 (+B) - D40-17 (E) | B - B | Battery power supply | Always | 10 to 14 V |
| D40-17 (E) - Body ground | B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the D40 ECU connector.
Measure the pulse according to value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| D40-10 (LIN) - D40-17 (E) | L - B | LIN Communication line | power switch on (IG) | Pulse generation |
| D40-18 (IG) - D40-17 (E) | G - B | Power supply | power switch on (IG) | 10 to 14 V |
| D40-18 (IG) - D40-17 (E) | G - B | Power supply | power switch off | 0 V |
| CHECK ID CODE BOX (IMMOBILISER CODE ECU) |

Disconnect the D31 ECU connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| D31-1 (+B) - D31-8 (GND) | W - V | Battery power supply | Always | 11 to 14 V |
| D31-8 (GND) - Body ground | V - Body ground | Ground | Always | Below 1 Ω |
Reconnect the D31 ECU connector.
Measure the pulse according to value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| D31-3 (LIN1) - D31-8 (GND) | LG - V | LIN Communication line | power switch on (IG) | Pulse generation |
| CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) |

Disconnect the D11 ECU connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| D11-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| D11-6 (IG2) - D11-1 (GND) | V - W-B | Power supply | power switch on (IG) | 10 to 14 V |
| D11-6 (IG2) - D11-1 (GND) | V - W-B | Power supply | power switch off | 0 V |
| D11-7 (B) - D11-1 (GND) | G - W-B | Battery power supply | Always | 10 to 14 V |
Reconnect the D11 ECU connector.
Measure the pulse according to value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| D11-5 (LIN) - D11-1 (GND) | GR - W-B | LIN Communication line | power switch on (IG) | Pulse generation |