Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › CONDENSER

CONDENSER > REMOVAL

for Preparation Click here



1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Turn the A/C switch on.

  1. Operate the A/C with the setting temperature at 25°C (77°F) and the blower level at LO for 10 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.

  1. Turn the power switch off.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.



2. REMOVE NO. 2 ENGINE ROOM SIDE COVER LH


    A173813
  1. Remove the engine room side cover.



3. DRAIN COOLANT (for Inverter)

NOTICE:
  1. Do not reuse the drained coolant because it may contain foreign objects.
  2. Collect the drained coolant and measure its volume to establish a benchmark. When adding coolant, make sure to add more coolant than the measured amount.

  1. Remove the inverter reserve tank cap.

    CAUTION:
    To avoid the danger of being burned, do not remove the inverter reserve tank cap while the coolant for the inverter is still hot.



    C109300
  1. Using a hexagon wrench (10 mm), remove the drain plug indicated in the illustration and drain the coolant.

    CAUTION:
    Use caution when handling coolant immediately after driving or in summer because it may be hot.

  1. Install the plug with a new gasket.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }



4. REMOVE COOL AIR INTAKE DUCT SEAL


    B181107
  1. Remove the 11 clips and cool air intake duct seal.



5. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A173489
  1. Remove the 2 bolts, 4 clamps and air cleaner cap sub-assembly.

  1. Remove the air cleaner filter element from the air cleaner case sub-assembly.



6. REMOVE RADIATOR GRILLE


    B181108E01
  1. Put protective tape around the radiator grille.



    B181109
  1. Remove the 2 bolts and 4 clips.



    B181110
  1. Disengage the 6 claws and 4 guides, and remove the radiator grille.



7. REMOVE HOOD LOCK ASSEMBLY (w/o Engine Hood Courtesy Switch)


    B174188
  1. Remove the hood lock nut cap.



    B174189
  1. Remove the 3 bolts.



    B174190
  1. Disconnect the hood lock control cable and remove the hood lock assembly.



8. REMOVE HOOD LOCK ASSEMBLY (w/ Engine Hood Courtesy Switch)


    B174191
  1. Disconnect the connector.



    B174192
  1. Remove the hood lock nut cap.



    B174193
  1. Remove the 3 bolts.



    B174194
  1. Disconnect the hood lock control cable and remove the hood lock assembly.



9. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY


    A176030E01
  1. Detach the 3 hood lock control cable clamps from the upper radiator support sub-assembly.

  1. Remove the bolt and discharge hose bracket.

  1. Remove the 4 bolts and upper radiator support sub-assembly.



10. REMOVE HOOD LOCK SUPPORT SUB-ASSEMBLY


    A175943
  1. Disconnect the 2 connectors.

  1. Remove the 2 clamps and clip.

  1. Remove the 2 bolts and hood lock support sub-assembly.



11. REMOVE RADIATOR ASSEMBLY


    A173815
  1. Slide the clamp, and disconnect the water hose from the radiator assembly.



    A173816
  1. Slide the clamp, and disconnect the water hose from the radiator assembly.



    A173817
  1. Remove the 4 bolts and radiator assembly from the cooler condenser assembly.



12. DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY


    E153500
  1. Remove the bolt and disconnect the discharge hose sub-assembly from the condenser.

  1. Remove the O-ring from the discharge hose sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



13. DISCONNECT COOLER REFRIGERANT LIQUID PIPE A


    E153501
  1. Remove the bolt and disconnect the cooler refrigerant liquid pipe A from the condenser.

  1. Remove the O-ring from the cooler refrigerant liquid pipe A.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



14. REMOVE COOLER CONDENSER ASSEMBLY


    E153502
  1. Remove the 4 bolts.



    E153503
  1. Remove the cooler condenser assembly as shown in the illustration.